Clock Dial Design Round Metal Dial

Please remember to remove the protective plastic coating from the dials before use. The sized listed below are the overall width from side to side.


Round Clock Dials Gold Round Metal Dial

This will come with a plastic coating to be removed. The measurement given is the width from side to side of the dial.

Item #RD2

Round Clock Dials Ivory Round Metal Dial

The width of the dial is the measurement of the material from one side to the other over all. The dial will come with a removable plastic coating.

Item #RD3

Round Clock Dials White Round Metal Dial

Please remember to remove the protective plastic coating from the dials before use. The sized listed below are the overall width from side to side.

Item #RD4

Round Clock Dials 7 7/8 Round Embossed Dial

Heavy 7 7/8 inch wide dial with a Embossed center. The dial has a single hole for the clock hand shaft drilled. This quality dial has a white time ring with Arabic numerals.

Item #RDEMB778WAGT $60

Round Clock Dials Hermle 1161-853 Series

Round dial punched for a Hermle 1161-853 clock movement with the mounting feet on the back. This dial is high quality, all-metal, German-made dial with a white face, brass bezel, brass finished numerals and an aluminum backing. This 13" wide dial has a 1-3/4” diameter seconds bit and a 11” diameter timetrack.

Item #RD1161WAGT $75

Round Clock Dials Banjo Style Dial

Painted metal round banjo clock dial. This dial is 7 1/2 inch round with a 6 inch time track and is an excellent old style look. If using with a spring movement, the winding holes will need to be drilled.

Item #RDBJ75 $50

Round Clock Dials

6 1/2 Vienna Style

Thin metal 6 1/2 inch Vienna style clock dial. The dial is white with black Roman numerals and a gold tone trim.

Item #RD65WRGT $15

Round Clock Dials Hermle Punched Dial

Painted metal round clock dial with the four rear stand off posts. The 7 1/4" wide has a 6 1/2 inch time track drilled to fit many Hermle clock movements. This will line up for the following movements 351-020 351-030 350-020 350-030 1050-020 1050-030 1051-020 1051-030

Item #RD351WRGT $60

Round Clock Dials Round White Gold Trim

Round 8 inch clock dial with white face and Roman numerals and a gold trim. This dial will need to be drilled to wind the clock if using a spring driven movement.

Item #RDWRGT8 - $60

Round Clock Dials Heavy Paper Stock Dial

Select Arabic or Roman Numerals, White or Ivory. Measurements are from outside the numeral on one side to outside the numeral on the other side of the round clock dials. (The timetrack diameter)


Round Clock Dials 6 1/2 for 241-840

White dial with black Arabic numerals. This dial is 6 1/2 inch wide overall. It is drilled for the winding arbors on a Hermle 241-840 series clock movement.

Item #RD7WAGT $20

Round Clock Dial Assortment Round Dial Assortment

Ten piece clock dial assortment made of heavy paper stock and plastic. Sized dials from 4 inch to 11 inch assorted. These dials can be glued to a wooden back board and used for many quartz clock projects.

Item #RD14 $7

Clock Parts Dial Grommets Dial Grommets x3

Set of three dial key hole grommets. These are what make the key holes pretty where you wind the clock through the dial.

Item #CP32 - $2.

Spring Drive Movement Note

Most of these round clock dials are not punched for the winding arbors for a spring driven movement, unless specified with the movement number.

If you have a spring driven clock movement then you would need to drill out the dial so you can wind the clock. We offer dial hole grommets so the holes will be pretty when you're done on hardware page.

Product Information

The paper dials on this page come square but have a round time track. This means you would need to cut the dial to fit your needs.

The round metal dials may come with a protective plastic coating that is removed by the customer, it is hard to tell it is there sometimes but if the dial has scratches, it most likely has this coating that needs to be removed for the finished clock project.