Mainspring Winder
Winder for loop end mainsprings, to be used with the mainspring
wheel and a mainspring clamp next item over. This is a tricky tool to use so
please read up on working with mainsprings in our Ebook.
Item #CT1-- $23
|
Mainspring Clamps
Set of 4 mainspring clamps keep a mainspring in the wound
position to keep them under control. Best to get two of these sets for paired
sized mainsprings.
Item #CT2-- $13
|
Oiler with Oil
Fountain oiler filled with general clock oil. Convenient
applicator to get into tough areas. This is the oil you need to lubricate your
clock.
Item #CT3-- $15
|
Clock Oil
Regular clock oil in a 20ml bottle. Same as the oil next
item over but you get more of it. This does not have an applicator but you can
use a needle or a toothpick to put one drop at a time to where the clock
movement needs it.
Item #CT27-- $15
|
Hand Remover
Removes stubborn hands and gears in a straight motion. This
tool is needed on many 400 day clock hands that a stuck on as well as pulling
gears off of the back of triple chime Hermle movements.
Item #CT10-- $15
|
Assorted Files
Set of 12 needle files for various uses in clock repair.
There are many assorted shapes.
Item #CT6-- $15
|
5 Prong Keys
. These two 5 prong clock keys
will wind almost all wall or mantle clocks. Get the USA made key set for the better quality
or the India made for the low price.
Item #CT7
|
Cutting Broaches
6 Broaches for larget watches and Small clocks. There are
different sizes in this assortment. These are used to ream out pivot holes and
get them ready for a new bushing.
Item #CT8-- $27
|
5pc Tweezers
Stainless steel tweezers set of five various styles.
Useful to reach into a clock movement to arrange the wheels as your assembling a
movement. One each AA, MM, NN, 3 and 5 in a plastic pouch.
.
Item #CT36-- $15
|
Movement Supports
Keeps the movement up and stable during an overhaul. Just
tighten one post on each corner to work on the clock movement as its in the air.
Set of 4 posts 3 3/4" long. This is the correct sized post to use with a
grandfather movement or other movements with the strike hammer in the back.
Item #CT32-- $44.
|
6 Large Broaches
Assorted sized clock broaches for larger clock
movements. These are used to ream out a pivot hole diameter and get it ready to
put in a new bushing.
Item #CT11-- $33
|
7 Closing Punches
Spring loaded tips on these tools. These take a
hole diameter and make them smaller. These are to be used with a small hammer.
Item #CT12-- $48
|
Centering Punch
This has adjustment for a heavy or light punch. This tool is to
prick punch a movement. This is not recommended but it is a way out of needing
to bush a pivot hole. Just put this tool on the oblong side of a out of round
hole and push it in or hit it with a small hammer to make the hole round again.
Item #CT13-- $15
|
Precision Screwdrivers
Set of nine precision screwdrivers set in a wooden Box.
Assorted sizes for small screws.
Item #CT38-- $20
|
Pivot Tool
Perfect tool for assembling clock movements and trying
to reach hard to reach pivots and arbors. Use this tool to arrange wheels in a
disassembled movement that is going together.
Item #CT15-- $10
|
Wooden Bench Key
Used to release the power in a wound up mainspring. This
will go over your existing key and let you release the power in a safe manner as
you release the click.
Item #CT21-- $15
|
Vision Visor
Flips up and provides 2 1/2x power, can be worn with
eyeglasses. Very useful magnification.
.
Item #CT25-- $20
|
Pin Vise Set
Set of 4 with capacities from .0mm to 4.65mm. Good to use
on broaches when reaming out a pivot hole diameter. Grabs hold of a post of some
sort so you can work with it basically. Small part of the pinvise is knurled so
it can be easily rotated.
.
Item #CT18-- $23
|
Punch Set
16 Piece set of anvils and stakes for clockmakers. 16 assorted
punches: 4 flat-faced hollow, 10 round-faced hollow and 2 assorted hole closing
sizes. Large hardened steel anvil with 10 holes of graduated sizes. Complete
with wooden set holder.
Item #CT44-- $58
|
Nylon / Brass Hammer
Nylon head on one end and brass on the other. Good
for doing light tapping on something you do not want to get damaged.
Item #CT33-- $15
|
Movement Test Stand
Works great on testing mantle clock movements.
Durable, practical, adjustable and well made.
Item #CT24-- $75
|
Clock Staking Set
Clock Staking Set in a wooden closable container. These
sturdy stakes have various hole diameters in the ends to fit the task at hand.
.
Item #CT47-- $50
|
Clock Repair Ebook
Basic clock repair and trouble shooting with this
downloadable Ebook. Learn about Floor clocks, mantle clocks, anniversary clocks
and cuckoos
.
Item #CT48-- $23
|
0-25 Micrometer
Readings of 0-25mm in this small useful tool. Good
for reading the diameter or thickness of many clock parts.
Item #CT31 -- $19
|
Orange Wood
Good for cleaning pivot holes, can be sharpened to a
fine point to get in the Smallest holes. Comes as a bundle.
Item #CT37-- $5
|
Let Down Tool Set
Used to release the power in a wound up mainspring.
Key goes into the chuck and the chuck goes into the handle so you can let down
the power of the spring. Basically the same thing as CT21 but with a better
design.
Item #CT20-- $29
|
Broach with Handle
This 8" long tool is to increase the diameter of a hole in a
clock plate so a bushing can be used. The end of it is squared not round at the
point.
Item #CT5-- $15
|
Pin Pusher with Handle
This 6" long this tool is to prick punch a movement. This is
not recommended but it is a way out of needing to bush a pivot hole. Just put
this tool on the oblong side of a out of round hole and push it in or hit it
with a small hammer to make the hole round again.
Item #CT9-- $10
|
|
|