Hermle Clock Movements

HERMLE MOVEMENTS

We offer only the best grade of clock movements with no plastic components

Every clock movement comes with a 2 year warrantee

Less cost than a cleaning in most cases
Should last 25-30 years, a repair would not
Easy to install, we can help if needed
Ships same day as order

HOW TO ORDER:

Hermle uses a 6 or 7 digit number code to designate whether it is spring, chain, or cable driven, the plate size, hammer arrangement, and the hand shaft length.

Back Plate Example:
77
Howard Miller
1161-853
94cm

The above example shows the movement number 1161-853. Hermle made this movement for Howard Miller and its three pendulum components total 94cm long. To get a new replacement movement for this clock, the first set of numbers would be matched up with the below chart. In this case 1161 would be selected below and all the movements that start with 1161 will come up in a webpage for you to select from.

Movements may vary from the picture

The matching of the movement number is what makes the difference, if the old movement number matches on the list, then you will get that exact same movement.

NOTE:

Hermle makes movements for various cabinet makers and marks there name onto the movement, so you may have a Hermle movement even it has a different name on it. Some other names made by Hermle are Seth Thomas (the newer Seth), Tally Industries, Howard Miller, Mason & Sullivan and others.

ALSO NOTE:

Many of the Hermle movements have been improved upon by the factory over time. Some have bronzed bushings in key wear areas to increase the life of the movement, and on the non-pendulum units the balance has been improved upon for longer life and ease of timing.

130+131+132	140+142	241	261	340+341	350+351
451	461+471	1050+1051	1151	1161	1171

WHO MADE IT	OTHER NAMES USED	EXAMPLES	DESCRIPTION	AVAILABILITY

HERMLE	Howard Miller Welby Ridgeway Larose Talley Industries Mason & Sullivan Seth Thomas Buliva Hamilton	1161-053 114cm Or 340-020 Or 451-050 94CM And similar	Three or four numbers followed by a dash, then a CM length underneath it if there is a pendulum. They are all consistent as they always have the numbers, then a dash, then more numbers. Basically if there is a dash in the movement number, and its all numbers in the beginning with no letters like "A", and the clock was made in Germany, its a Hermle unit for sure.	Excellent availability at this time, we stock all Hermle units, with very few exceptions. Some special CM lengths maybe special order, if its not on the charts then it most likely will have to be made up special for an extra $20, this is a special order so please call it in. Hermle is the biggest movement producers in the world today. Not only do they have the most movements being made, but they also have the best part availability when you need a component such as a pendulum or a dial, or a complete clock kit. Hermle units generally last 22 to as much as 35 years. We usually get calls to replace units that were built in the early 80's or late 70's. If you look at the back plate of the movement you will see a couple numbers above all the other numbers. You will see such as a 77 or an 83 or so on. This is the date the movement was built. Replacing these units rather than getting them cleaned and oiled is usually the smart way to go as it is factory improved, brand new, factory lubricated, easy to install, and it will cost less than a cleaning. Keep in mind however that there are different grades of the same movement number, some are cheaper and contain plastic parts. The Hermle units that we offer here at Clockworks are the best grade available with no plastic components for a very reasonable price.

WHO MADE IT

OTHER NAMES USED

EXAMPLES

DESCRIPTION

AVAILABILITY

HERMLE

Howard Miller
Welby
Ridgeway
Larose
Talley Industries
Mason & Sullivan
Seth Thomas
Buliva
Hamilton

1161-053 114cm

Or

340-020

Or

451-050 94CM

And similar

Three or four numbers followed by a dash, then a CM length underneath it if there is a pendulum. They are all consistent as they always have the numbers, then a dash, then more numbers.

Basically if there is a dash in the movement number, and its all numbers in the beginning with no letters like "A", and the clock was made in Germany, its a Hermle unit for sure.

Excellent availability at this time, we stock all Hermle units, with very few exceptions. Some special CM lengths maybe special order, if its not on the charts then it most likely will have to be made up special for an extra $20, this is a special order so please call it in. Hermle is the biggest movement producers in the world today. Not only do they have the most movements being made, but they also have the best part availability when you need a component such as a pendulum or a dial, or a complete clock kit. Hermle units generally last 22 to as much as 35 years. We usually get calls to replace units that were built in the early 80's or late 70's. If you look at the back plate of the movement you will see a couple numbers above all the other numbers. You will see such as a 77 or an 83 or so on. This is the date the movement was built.

Replacing these units rather than getting them cleaned and oiled is usually the smart way to go as it is factory improved, brand new, factory lubricated, easy to install, and it will cost less than a cleaning. Keep in mind however that there are different grades of the same movement number, some are cheaper and contain plastic parts. The Hermle units that we offer here at Clockworks are the best grade available with no plastic components for a very reasonable price.