Kieninger Clock Movement

1-888-200-7445
Providing clock movements for Kieninger

Help finding a replacement Kieninger clock movement:
First thing to do is to get all the information off of the back plate of the Kieninger clock movement itself and write it down. Be sure to remove the weights and pendulum if the case is to be moved to see the back plate of the movement. Do not make the mistake of looking for the model number of the clock, this number is on the paperwork that comes with the clock and is not what is needed to replace the Kieninger movement. As stated above, the information needed is located on the back plate of the movement itself.

The numbers off of the Kieninger clock movement's back plate are not always very helpful in determining what the movement is. You may have a number such as this: 84 R 80CM. In this case 84 is the year, R is the beginning of the series number that you must finish figuring out what it is, CM is the pendulum length in centimeters from the suspension post all the way down to the bottom of the pendulum. You must still figure out the Kieninger series number, or at least the rest of it. You do this by looking at the below charts.

So to find out what Series movement you have, the first thing you do is determine if your clock is run by weights or springs, and if weights then how many. This will tell you what chart to use. Then determine the chime, if its Westminster, triple chime, Bim Bam or gong. You can tell if the clock is a Westminster will have 8 hammers, Triple chime will have 12 hammers,. Bim Bam will have only 2 or three hammers and gong will only have one. Next is the hand shaft length. This is measured from the front plate of the movement all they way out to the end of the minute hand threads.

THREE WEIGHT CLOCKS

Movement #	Chime Type	Driven by	CM length	Handshaft	Picture	Price

HTU	Triple Chime	Cable Driven	116cm	56mm		$2400
H0001	Westminster	Chain Driven	116cm	56mm	[Picture]	$699
HK002	Triple Chime	Chain Driven	116cm	56mm		$725
HSU	Triple Chime	Cable Driven	116cm	56mm	[Picture]	$719
KK 25	Westminster	Chain Driven	116cm	47mm	[Picture]	$399
KKU 26	Triple Chime	Chain Driven	116cm	47mm	[Picture]	$449
KS 57	Westminster	Cable Driven	116cm	47mm	[Picture]	$399
KS 58	Westminster	Cable Driven	100cm	47mm	[Picture]	$399
KSU 33	Triple Chime	Cable Driven	116cm	47mm	[Picture]	$449
KSU 36	Triple Chime	Cable Driven	100cm	47mm	[Picture]	$449
KSU 38	Triple Chime	Cable Driven	93cm	47mm	[Picture]	$449
KSU 50	Triple Chime Seq	Cable Driven	116cm	47mm	[Picture]	$499
KSU 51	Triple Chime Seq	Cable Driven	93cm	47mm	[Picture]	$499
KSU55	9-BELL BASE	Cable Driven	116cm	47mm		$449
KSU63	BEETHOVEN	Cable Driven	116cm	47mm		$749
KSU66	W/CAROUSEL	Cable Driven	116cm	47mm		$749
MS	Westminster	Cable Driven	116cm	47mm	[Picture]	$459
MSU	Triple Chime	Cable Driven	116cm	47mm	[Picture]	$459
RK 014	Westminster	Chain Driven	80cm	36mm	[Picture]	$399
RK 022	Westminster	Chain Driven	93cm	36mm	[Picture]	$399
RK 023	Westminster	Chain Driven	116cm	36mm	[Picture]	$399
RK032	Westminster	Chain Driven	116cm	48mm	[Picture]	$399
RU010	Triple Chime	Chain Driven	116cm	36mm		$399
RU012	Triple Chime	Chain Driven	93cm	48mm		$399
RU013	Triple Chime	Chain Driven	116cm	48mm		$399
RU027	Triple Chime	Chain Driven	93cm	36mm		$399
SK18 REAR	Westminster	Chain Driven	116cm	36mm	[Picture]	$299
SKS12,13	Westminster	Chain Driven	116cm	36mm	[Picture]	$299

TWO WEIGHT CLOCKS

Movement #	Chime Type	Driven by	CM length	Handshaft	Picture	Price

PSO26	Gong Strike	Cable Driven	65cm	32mm	[Picture]	$349
PSO27	Gong Strike	Cable Driven	80cm	36mm	[Picture]	$349
PSO37	Gong Strike	Cable Driven	80cm	32mm	[Picture]	$349
PSO38	Bim Bam	Cable Driven	80cm	32mm	[Picture]	$349
PSO39	Bim Bam	Cable Driven	65cm	32mm	[Picture]	$349
PSO40	Bim Bam	Cable Driven	80cm	36mm	[Picture]	$349

SPRING DRIVEN

Movement #	Chime Type	Driven by	CM length	Handshaft	Picture	Price

J0204-01	Triple Chime	Spring Driven	Balance	32mm	[Picture]	$419
J0218-04	Triple Chime	Spring Driven	Balance	36mm	[Picture]	$419
J0219	Triple Chime	Spring Driven	Balance Back Wind	36mm	[Picture]	$479
J0236	Triple Chime	Spring Driven	Balance	48mm	[Picture]	$419
J1204	Triple Chime	Spring Driven	43cm	36mm	[Picture]	$419
J1208	Triple Chime	Spring Driven	54cm	32mm	[Picture]	$419
J1212	Triple Chime	Spring Driven	35cm	36mm	[Picture]	$419
J1213	Triple Chime	Spring Driven	35cm	32mm	[Picture]	$419
J1216	Triple Chime	Spring Driven	48cm	48mm	[Picture]	$419
J1218	Triple Chime	Spring Driven	43cm	48mm	[Picture]	$419
AEL-01	Westminster	Spring Driven	Balance	32mm	[Picture]	$259
AEL-03	Westminster	Spring Driven	Balance	36mm	[Picture]	$259
SEW	Triple Chime	Spring Driven	Balance	32mm	[Picture]	$319
RWU-03	9-Bell Top	Spring Driven	15cm	36mm	[Picture]	$1100

ONE WEIGHT, TWO SPRING CLOCKS

Movement #	Chime Type	Driven by	CM length	Handshaft	Picture	Price

RWS13	Westminster	Cable/Spring	65cm	36mm	[Picture]	$449
RWS20	Westminster	Cable/Spring	116cm	36mm	[Picture]	$449
RWS22	Westminster	Cable/Spring	116cm	36mm	[Picture]	$449
RWS23	Westminster	Cable/Spring	80cm	36mm	[Picture]	$449
RWS25	Westminster	Cable/Spring	116cm	48mm	[Picture]	$449
RWS31	Westminster	Cable/Spring	116cm	36mm	[Picture]	$449

About Kieninger

Kieninger is the oldest existing manufacturer of mechanical movements for floor, wall and mantel clocks in the world. The Kieninger movement excel with a high level of design and manufacturing quality. Numerous innovations and patents (16-rod chimes; second indication for pendulum lengths under 116 cm; automatic beat adjustment, nighttime shut-off systems for 1/2-hour and 1/4-hour movements; automatic chime sequencing; various manufacturing processes and components) are the measure for design quality.

Manufacturing quality shows in every movement: All movement plates are made of a special brass alloy which is hard and has a tensile strength of 53 kp/mm2. The holes for the journals are reamed and smoothened after lacquering and then receive an oil sink.

Pinions are made of high-quality steel or stainless steel. Fast turning pinions are hardened. All journals are roller burnished in a special process. Some movements feature bronze-bushings and/or jewels in critical positions. The gears are made of a very tough and hard brass alloy with a tensile strength of 62 kp/mm2.

A high level of corrosion protection for all components is assured. Brass components are pickled and receive a coat of clear lacquer. Steel components are made from stainless steel or receive a galvanic nickel coating. Each Kieninger movement has a laser engraved serial number.