Search results: “German hands”

German Regulator Style Clock Hands
Removing the Mechanical Clock Hands

Removing Mechanical Clock Hands Removing Mechanical Clock Hands is fast and easy to do. The following are hand removal instructions for German mechanical movements post WW2. German Post WW2 wall, mantle and floor models Removing mechanical clock hands for post WW2, mantle and floor clocks is quite simple. Turn the hand nut to the left while holding the minute hand with your fingers. Use some small needle nose pliers to loosen the nut first. Once the nut is loose, turn...

See more articles about German hands ⇲

Showing 1–16 of 40 results

  • launch

    View Product

    View more

    turned_in_out Hermle Quartz Clock Movements

    New Quartz Chiming Movement

    Replacement movements for the German made Hermle quartz. These chiming units take two C-cell batteries and play two different songs. Well made quartz movements that last for a long time. The old units seem to give up the ghost during daylight savings when they do die.

    MSO-B: $80.00
    View Product
  • launch

    View Product

    View more

    turned_in_out German Mechanical Clock Hands

    Spade Variant Clock Hands for German Clocks

    Hour and minute Spade Variant Clock Hands that fit most German mechanical clock movements made after 1950. These are for a 6 inch time track. The measurement of the time track is how to get the correct length of hands. A time track is the small ring outside of the numerals.

    RC30: $20.00
  • launch

    View Product

    View more

    turned_in_out German Mechanical Clock Hands

    Serpentine Mechanical Clock Hands

    This is a set of Serpentine Mechanical Clock Hands that fit most German mechanical clock movements made after 1950. Measure the hands by the time track diameter. A time track is the small ring outside of the numerals.

    CH3Hands: $16.00 - $35.00
    View Product
  • launch

    View Product

    View more

    turned_in_out German Mechanical Clock Hands

    Mechanical Clock Spade Hands

    Spade hands that fit most German mechanical clock movements. Measure the hands by the time track diameter. A time track is the small ring outside of the numerals. The minute hand length will be about half this diameter.

    CH1: $20.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Mechanical to Quartz Conversion

    Regulator Style Clock Hands for Hermle

    Here are Regulator Style Clock Hands that fit most German mechanical clock movements made after 1950. The hands are measured by the time track diameter. A time track is the small ring outside of the numerals.

    CH8: $16.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Wall or Mantle Clock Kits

    Mechanical 2-Weight Vienna Clock-Kit

    This is an 8 day, Vienna regulator wall clock kit with a German made Hermle clock movement. Kit comes complete with all pieces to put together a complete clock with the exception of the clock case.

    WMKIT14: $1,000.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Wall or Mantle Clock Kits

    German Mechanical Mantle Clock Kit

    Bell strike wall clock kit’s minimum case requirements are 3 1/4″ deep, 6″ wide with the dial (4 3/4″ with out), 6″ tall with the dial. Like a mechanical watch, this has a balance escapement. Therefore it does not need a pendulum.

    WMKIT5: $300.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Wall or Mantle Clock Kits

    Mechanical Westminster Vienna Clock Kit

    Mechanical Westminster Vienna clock kit's minimum case requirements are 4 1/2″ deep, 8″ wide. The Pendulum length comes in 55cm, 66cm, 75cm, or 85cm. This CM is the overall length of the pendulum from the TOP of the movement and down.

    WMKIT13: $1,165.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Wall or Mantle Clock Kits

    Westminster Vienna Regulator Clock-Kit

    Westminster Vienna Regulator Clock-Kit has a minimum case requirement of 4 1/2″ deep, 7 1/2″ wide. Pendulum length 66cm, 75cm, or 85cm. This CM is the overall length of the pendulum from the TOP of the movement and down, based on the lightest pendulum possible.

    WMKIT7: $1,200.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Grandfather Clock Kits

    Tubular Bell Grandfather Clock Kit

    Tubular Bell Grandfather Clock Kit is one of the finest quality clock movements made in modern times. Specifically, it plays 4/4 Westminster, Whittington, or St. Michael's chimes each quarter hour and strikes the full hour.

    GFKIT4: $3,900.00
  • launch

    View Product

    View more

    turned_in_out Chain Driven Movements

    H Series Kieninger Clock Movement Conversion

    H Series Kieninger Clock Movements boast large 6 x 9 plates, utilize chain driven technology, and proudly display the Kieninger name along with a CM number (like 116cm) on the movement itself. These units are no longer available. What is being sold is a conversion kit for an alternate movement with great durability. Comprehensive Floor Clocks Manual Explore our in-depth... View Product

    KIEN-H: $700.00 - $750.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Grandfather Clock Kits

    Kieninger Grandfather Clock Kit

    The Kieninger grandfather clock kit boasts a cable driven, triple chime, German movement. Plays 4/4 Westminster, Whittington, or St. Michaels chimes quarterly. Complete with hands, crank, chime block, weights and shells, pulleys, lyre pendulum and 11 x 15 1/2 moon dial.

    GFKIT3: $1,900.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Grandfather Clock Kits

    Round Dial Grandfather Clock Kit

    Round dial grandfather clock-kit's minimum case requirements are 8" deep, 12" wide, 52" tall. Any smaller clock case and this kit will not work. The German made grandfather clock movement is triple chime and cable driven.

    GFKIT6: $1,600.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Grandmother Clock Kits

    Side-Strike Tall Case Clock Kit

    Side-Strike Tall Case Clock-Kit has a minimum case requirement of 4″ deep, 11″ wide including the dial (6 1/2" without), 49″ tall with the dial. Has a 100cm (39 1/2") pendulum length from the top of the movement and down.

    GMKIT8: $950.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Grandmother Clock Kits

    Bell Strike Clock Kit GMKIT7

    This quality chain driven Bell clock kit will strike the hours on a bell. On the half hour it will strike only once.

    GMKIT7: $750.00
  • launch

    View Product

    View more

    turned_in_out Wall or Mantle Clock Kits

    Mechanical Wall Clock Kit WMKIT1

    Westminster spring driven kit's minimum case requirements are 4″ deep, 8″ wide, 18 1/2″ tall with the dial. In addition, this German made clock movement has a 45cm (17 3/4") pendulum length from the TOP of the movement and down.

    WMKIT1: $450.00