- Hermle Clock Kit 131-081 18cm
- Two bells on back
- 8 day Spring Driven
- Brass rod pendulum
- German made movement
- 2-year warranty
You may ask what is the difference between the WMkit6 and the WMkit3, and the differences are slight. The two bells are sticking out of the backside of the WMkit3 unit, where as the bell set in WMkit6 are smaller and within the movement. The WMkit3 has a 33.2mm hand shaft length, and the WMkit6 has a 27.2mm hand shaft length. This is the shaft that the clock hands go on, measured from the front plate of the movement and all the way out to the end of the minute hand nut threads.
This is a quality 8 day, German made, gong strike, spring driven movement. It has the popular 131-081 18cm Hermle clock movement with the two hammers on the back that strike bells (included).
Here are some measurements you need to know to build your case, but of course the best thing to do is to get the movement first and then build the case afterward. The hand shaft, (shaft that the hands go on) is 27.2mm from the front plate and all the way out. The pendulum length on this unit is measured from the top of the clock movements suspension post and all the way down. This measurement is 18cm and includes the pendulum tip to tip, the leader it hangs on, and the suspension that the leader hangs on.
The kit comes with the movement, gong with mount, the pendulum, hands and a key. This is a complete clock with out the wood case or clock dial, you would use your old dial if you can or get a new dial and drill it out to wind the clock. The clock case would be typically a shelf style and this is to be built on the customers end.
This is a nice compact quality made round unit that runs for 8 days on a wind. Mounting the movement is usually done in the front with the front movement mounts (included).
The special pricing on this kit is only due to the fact that we happen to have overstock on them. As you can see the price is below even the price of a movement alone, and you get everything mentioned.
Movement with leader and hand nut
Two bells premounted
Dog ear style mounting brackets
Pendulum with its bob and nut
Serpentine Hands for a 6 inch dial
Number 4 Brass Key
Nut driver ¼ inch size
Needle nose pliers
Small brass finishing nails
Medium sized Phillips screwdriver
Some small wood screws
Thank you for purchasing this clock kit! This is a quality German made Hermle 8 day key wind movement that will withstand the test of time. Here are some simple instructions to get you on your way.
1. Adjust the bell hammers
The mounted two bell strike system will need some final adjusting before mounting the movement. This is because during shipping the hammers may not be aligned for a crisp musical bell tone. The hammer heads need to be away from the bell at rest, about 1/8 inch away. This is adjusted with your fingers just bend the hammer head wire up / down / side / side to get the hammer heads into position at that 1/8 inch away measurement. This will produce a nice bell sound with out thudding, double hitting, or missing the bells completely.
2. Mount the Movement
The Hermle 131 movement series is pretty diversified with its mounting capabilities as it can be mounted in the front or the back depending on your needs. It is best to come up with a mount that allows the back of the movement to be accessed without too much hassle, in case you need to change the suspension spring at some point or if the leader needs to be adjusted.
For a front mounting method you would use the enclosed dog ear looking brackets and put them on the front plates pillar posts, under the hex nut that is holding the front on. Of course you would want to do only one at a time so the movement does not come apart on you, just remove one hex nut, put the bracket on, and then put the hex nut back on. Then do the rest the same way, one at a time. Since this is a front mount you’re going with, the movement will get attached to the front of the clock case with a board between the front of the movement and the clock dial.
This will either go into the back of the clock case or a wood mount that will support the movement but at the same time not get into the way of the pendulum assembly at all. If you choose to mount in a different fashion this is fine just take these long posts right off.
3. Mount the Dial
This movement kit does not include a clock dial, the dial needs to be picked out by the customer and drilled for this movements winding arbors on the customer end. The larger clocks are easy because customers usually want generally the same dial but with some minor differences. With these smaller units there are too many design possibilities to offer an array of pre-punched dials for this movement series. Please review our dial offerings as a separate purchase and or give us a call to discuss the options 800-381-7458
4. Install the Hands
After the dial is mounted it’s time to put the hands on the clock. First comes the hour hand that is installed only in a friction fit. You put the hour hand on and twist and push down toward the dial at the same time. The more down the hour hand is toward the dial, the tighter fit it is as the hour hand post is tapered. You want it on fairly snug but not touching the dial or the minute hand that comes next. The hour hand, the dial, the minute hand should all be parallel with each other and not hitting each other during any part of their rotations.
Hands for these modern German units are designed with a rotate-able center mount in the minute hand. You need to know this as when you set up the clock at first it will not strike exactly on the hour or quarters like it should. To correct this issue it is only needed to take the minute hand off and use needle nose pliers to spin the center mounting bushing independent of the hand itself. You hold the minute hand in one hand, the needle nose pliers in the other while grabbing and spinning this center hand bushing. What this does is align that square hole in the way you need it to mount so the hand is pointing to the correct time when it chimes.
5. Install the Pendulum
The pendulum assembly consists of three components and the Germans measure all of them in one measurement. The measurement is stamped on the back plate of the movement itself in CM. The three components are the suspension spring on the very top, the leader it hangs on, and then the pendulum length all the way down to the very bottom of the pendulum rating nut threads.
When you get the movement the suspension spring will be installed but not always the leader that hangs on it. This you would put on as follows: Take the set screw out of the suspension post as to release this suspension spring and then lower it with your fingers. When the spring is lowered you are able to hook on the leader hook top, and you at the same time need that leader engaged with the crutch that swings back and forth on the back of the movement. So in other words, you will have the leader in the center of the crutch that swings it, as you hook the top to the suspension. With the leader attached to the suspension you can then bring the two part assembly up and back home into its suspension post and put in the set screw again. Now the movement is ready for casing and to be aligned with the chime block as described above. After the movement is cased and ready to go, you just hang the pendulum onto the bottom of the leader and put it in beat.
Please note !
Every pendulum clock needs to be put into beat to operate, if the clock is not put into beat it will run for 5 minutes to 12 hours and then stop every time. In many cases the complaint with a mechanical clock is that it stopped working after it was moved. This is usually from someone moving the clock without taking the pendulum off and this puts the clock out of beat. Out of beat is a term used in clock repair that basically means the clock is going tock-tick tock-tick instead of tick- tock- tick -tock. It is sometimes corrected by putting a matchbook or small piece of wood under one side of the clock case to make the tick and the tock evenly spaced. This can temporarily correct the problem and the clock runs fine. This method however is not as good as correcting the beat and having the clock run when it is truly straight and level.
You would adjust the beat by pushing the top of the pendulum left or right as it hangs in its clock case, just hold a lower portion of the pendulum with your left hand as you push the top of the pendulum left or right with your right hand. You will feel the freedom in the pendulum to move left or right, with some resistance at the sides at the end of your left or right travel. You are changing the beat of the clock when you go beyond this resistance and therefore changing the place of the freedom area. Don’t be afraid to move this pendulum top as there is nothing to break as you go left or right.
The pendulum is responsible for all the timekeeping of the movement. There is a rating nut on the bottom of the pendulum, this gets turned to get the time perfect. Timing a clock takes some time and patience to get perfect as you have to adjust it a few times to get it right. When turning this nut you are either raising or lowing the pendulums round bob at the bottom, and this positioning is what speeds or slows time. If you turn the nut to the right as to raise the bob, time will go faster, the opposite way to slow it down. The pendulum assembly consists of three components and the Germans measure all of them in one measurement. The measurement is stamped on the back plate of the movement itself in CM. The three components are the suspension spring on the very top, the leader it hangs on, and then the pendulum length all the way down to the very bottom of the pendulum rating nut threads.