Cuckoo Clock Parts

launch

question_answer 0 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

The lift wires travel from the movement up to the flaps of the old bellow tops. Furthermore, these wires are taken off in order to remove the cuckoo bellows. Usually this is done by opening the loop on the lower end of the lift wire. This is where it connects to the movement’s lift arm. Use a small flat head… View Product

launch

question_answer 36 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

The Grandfather Clock Weights Description on this web page will cover what is meant by weights and their parts. Any part of the weight is available on its own. We also offer complete weights. If needing a complete clock weight, we need to determine what the appropriate weight is for the clock. This requires getting the information off of the… View Product

launch

question_answer 4 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

These are the directions to get a German mechanical clock to chime on time. This means having the clock hands point to the right spot when the clock chimes. When replacing a clock movement, or getting new clock hands, either one, you will notice it will chime 5 minutes before it should, or 10 min after, something like this. This… View Product

launch

question_answer 1 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

A new cuckoo clock movement will be a fraction of the price of an overhaul on the old one. This is due to the time it takes to separate the plates, work on the movement, and then put it all back together again. This process is very time consuming. Then, if the movement fails the testing process, it all has… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

The most common Cuckoo Clock Repair Parts sold are the bellow tops and the hands. The bellow tubes are usually good to reuse on the clock, just the bellow tops have cloth that rip over time and therefore the clock will not cuckoo the time out. If the cloth is torn, you do not need to replace the entire cuckoo… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

Issues with the strike quantity on a cuckoo clock is a common ailment upon setting up a new movement. The clock will strike 12 o’clock and then 12 again at 1 o’clock or something like this. This has to do with the mechanical components behind the clock dial. Remove the hands and dial to get to that section of the… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

When the new cuckoo clock movement will not go into striking mode for the hours. The bird will not come out and the clock will not indicate what time it is with the cuckoo call. Here are some guidelines on what to check in this situation. There is a wire above the cuckoo door. This closes and locks into place.This… View Product

launch

question_answer 8 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

Installing the cuckoo clock hands bought from clockworks.com starts with removing the old hands. To remove the cuckoo hands will only need a pair of needle nose pliers. While holding the minute hand still (longer of the two hands) while loosening the minute hand nut with the pliers. Turning the hand nut in the counter clockwise direction while holding the… View Product

launch

question_answer 18 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

Upon installation of a new cuckoo clock movement this is a common issue. The Cuckoo clock door stuck open could be a number of things. Please check the following to see if it solves the issue of the door not closing all the way. If the pine cone weight that controls the cuckoo portion of the clock is not heavy… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

The first step in purchasing a new chime block is to determine the chime block style that is in the clock. The Styles are side, bottom and back strike. Figure out which style you need. Then, count how many rods are in the chime block. Measure through the chime block to get the length of the longest rod. Correspondingly, find… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

AmMechanical clock chain installation is fairly easy. It is not uncommon for the chains to sometimes fall off during shipping. If this should occur, all you have to do is loop them back over the ratchet wheels. Mechanical Clock Chains installation maybe required upon the new movements arrival. When getting the new unit, the chains may or may not be… View Product

launch

question_answer 0 Questions/Answers

View more

turned_in_notCuckoo Clock Parts

The weights may or may not all weigh the same however they usually do not. It is needed to know what weights goes on what chain or cable for most floor clocks in existence. Typically there is differences on the weights from left to right on a mechanical floor clock. This section is referring to post WW2 modern floor clocks… View Product