Clock Hands

Mechanical Clock Hands are the arms that point to the numbers 1 to 12 so you know what time of day it is. Clock hands come in a variety of lengths.

Mechanical Clock HandsHand RemovalHand InstallationOrdering Mech HandsChime On Time FixAbout Hand Nuts

Please view these information tabs to help with getting the Mechanical Clock Hands.

Removing Mechanical Clock Hands

Removing Mechanical Clock Hands is fast and easy to do. The following are hand removal instructions for German mechanical movements post WW2.

German Post WW2 wall, mantle and floor models

Removing mechanical clock hands for post WW2, mantle and floor clocks is quite simple. Turn the hand nut to the left while holding the minute hand with fingers. Use some small needle nose pliers to loosen the nut first. Once the nut is loose, you can turn it with fingers until it comes off. Then the minute hand will be able to wiggle straight off its square arbor and off of the clock. The hour hand is a friction fit, so just twist the hour hand back and forth and pull toward you until it comes off. If you have a second hand bit, that is only a friction also, so just grab it with fingernails, twist pull off.

American Antique time and strike

These type of movements come in two styles. If there is a minute hand nut, the first style is the same as above. Be very careful not to lose this hand nut. They are very hard to find and replace. The second style of mechanical clock hands will have a pin holding the minute hand on instead of a nut. This pin tapers, meaning it's fat on one side and skinny on the other. Just grab the fat side with needle nose pliers and yank the pin out. The minute hand will fall out with a washer. Save the washer and the tapered pin for ease of reinstalling the hands. If these items happen to get lost, Clockworks offers washers and taper pins for purchase, as well as replacement mechanical clock hands.

The content of this website is copyright by Clockworks and written by James Stoudenmire in year 2020

German Mechanical Clock Hand Installation

The installation of the clock hands on a German mechanical movement is reverse of removal. If either the movement was replaced, or the hands are new, the minute hand must be adjusted. This is so it will point to the correct time when it chimes.

Installing the hour hand

First comes the hour hand as a friction fit. Put the hand on its round post and twist and push toward the front front of the dial. Be sure it is not in contact with the dial at any point of its travel in the circle. This includes the base of the hour hand, it cannot rub against the hole in the clock face itself. As its only a friction fit, it can be turned to point to whatever hour it is, just with the fingers.

Installing the minute hand

The minute hand installation is done by putting the square hole in the hand, on the square post of the hand shaft. The bottom of the minute hand cannot be rubbing the hour hand tube or the hour hand. If it is, the hour hand has to be set lower on its tube. With the minute hand on its square post now its time to put the hand nut on. The nut goes on finger tight and then a little bit more with needle nose pliers to make it secure.

Mechanical Clock Hands

The German mechanical clock hands are sold by the time track diameter. When ordering these mechanical clock hands, this measurement is important. To clarify, the dial diameter is the measurement of the time track. This means from just outside the 9 straight across to just outside the 3. For example, if this time track diameter is 6 inches, then select hands for a 6 inch time track in the drop down list. Hands for a 6 inch time track will have a minute hand of about 2 7/8 long from the mounting hole to the end. The proportionally smaller hour hand will come with the minute hand. This is a vastly different way of measuring than the quartz clock hands. So be sure to follow these directions for measuring and not the ones for the quartz hands.

Ordering Hands

After getting the time track diameter measurement, it is time to choose a style for the mechanical clock hand. Under each style of hand, there is a drop down menu. Look to see if the style you chose comes in the size you need for the clock. Not all styles of hands come in the same sizes, so you might have to look at the different options available. The most popular styles of mechanical clock hands are the serpentine and spade hands. Remember, the minute hand will come a little less than half of this time track measurement. The hour hand will be proportional in size to the minute hand.

How they are sent

So, when ordering mechanical clock hands, remember that they come as a pair, hour and minute hand. They ship the next business day from Clockworks in Huntington MA USA, via the method you chose upon checkout.

The content of this website is copyright by Clockworks and written by James Stoudenmire in year 2020

Mechanical Clock Chime On Time

These are the directions to get a German mechanical clock to chime on time. This means having the clock hands point to the right spot when the clock chimes. When replacing a clock movement, or getting new clock hands, either one, you will notice it will chime 5 minutes before it is supposed to, or 10 min after, something like this. This page explains how to correct this situation. It is unbelievably fast and easy to do.

Working with the minute hand

After a new mechanical movement is installed, or if you are just installing a new set of hands, it maybe noticed the clock will not chime at the time it's supposed to. To correct this, take the minute hand off of the clock. This is the longer of the two hands. With this minute hand off of the clock, turn it upside down and look that it has a square hole where it attaches to the clock. This square hole is in a bushing that will rotate WITHIN the minute hand itself.

The correction

So, all to be done is just use needle nose pliers to turn this bushing ever so slightly. Put the hand back on the clock and see if it’s pointing to the correct place where it chimed. If it is, then it all set and it will point to the exact place it is supposed too. If it is still not right, take the hand off and try again. Once you get the minute hand to point where it just chimed you then set to the correct time.

The conclusion

It is really that easy, there is nothing to do with the clock itself, only the minute hand. In other words, to put it in a silly way, take the minute hand off of the clock and walk to the garage with it. Take it far, far away from the clock. When in your garage take needle nose pliers and turn the bushing within the hand itself. Then walk back to the clock and put it on. See if it's now pointing to the right spot.

Grandfather chime on time
Grandfather chime on time
Grandfather chime on time
Grandfather chime on time
The content of this website is copyright by Clockworks and written by James Stoudenmire in year 2020

Mechanical clock hand nuts

One of the most common parts a Mechanical clock needs is the hand nut. As previously stated, the older the clock the harder things are to find. The hand nuts Clockworks offer are for movements made after the 1930's.

Prior to 1930 clock hand nuts

There were not many standards on what the hand nut size should be on the early clocks. However, prior to around 1930 there is no telling what will work. In other words, it is literally trial and error. There was no standard hand nut size. Any hand nut we offer, may, or may not, work. This includes cuckoo hand nuts, American clock hand nuts, or German hand nuts. However, with even all of these assortments, there is a chance none of them will work on the clock.

Post 1930 clock hand nuts

Generally speaking, what we have to offer in the three types of clock hand nuts will cover most of the post 1930 Mechanical clocks. The cuckoo hand nuts fit about 80% of the post war German made cuckoo clocks. The American clock hand nuts fit many of the mechanical time strikes that were so popular. German hand nuts fit most post war German made mechanical clocks, with the exception being a few large grandfather clocks.

Clocks that do not take a hand nut

Not all clocks require a hand nut. Some antique mechanical clocks require a clock hand washer and a tapered pin instead. These secure the minute hand as an alternative to the hand nut. The washer may have a small square hole, or large, oblong or round hole. Clockworks offers an assortment of 100 clock hand washers that includes all the styles mentioned. A tapered pin is used to secure the hand with the washer on top of it. The taper pin is inserted into a hole in the end of the minute hand arbor to secure the washer and minute hand to the clock. A taper pin is a small brass or steel rod that is wide on one end and skinny on the other. Clockworks offers them in an assortment of 100 to ensure the right one is there.

The content of this website is copyright by Clockworks and written by James Stoudenmire in year 2020
Clock Hand Measurement

Hands For Mechanical Clocks

The Mechanical Clock hands in the list below are sold by dial diameter size. Alternately, this is not the same method as a clock that operates on a battery. Instead, determine the hands for mechanical clocks as an after effect of measuring the dial diameter. Furthermore, a time track is the outer ring that clocks sometimes have just outside the numerals. Measure the dial diameter from outside of the 9 to outside of the 3. For example, if you come up with 6 inches for this measurement, then order hands for a 6 inch time track. So, for a pair of hands made for a 6 inch time track would have a minute hand around 2 7/8 inches long.

German Mechanical

These mechanical clock hands are for German mechanical clocks that are post WW2 and includes most mechanical clocks after 1950. Post war clocks are made in either Korea, China, or Germany. Of course, the Korean and China clocks are pretty easy to identify as they usually say 31 day on it. If this is the situation and the clock says 31 day, these hands will not fit.

If you would like to be certain the clock is from Germany, look at the back plate of the clock movement itself. There will always be a stamp with an engraving that says Made in Germany. These mechanical clock hands will fit 90% of these clocks. Although there are some exceptions. Some tubular bell units and some of the older German units are a couple of examples. To be absolutely 100% sure these hands are correct, measure the width of the mounting post on the movement and match it up with the sizes they specify.

The content of this website is copyright by Clockworks and written by James Stoudenmire in year 2020

German Spade

Hermle german mechanical spade hands

For many dial diameters. These fit most German mechanical clock movements. The minute hand has a 2.2mm square mounting hole, the hour hand has a 4.5mm round hole.

CH1: $15.00$20.00
View Product

German Maltese

Hands For Mechanical Clocks

For Hermle mechanical movements as well as Urgos. 5" Dial diameter only.

CH12: $15.00

German Serpentine

German Serpentine Clock Hands

The most popular choice for German clock movements. These black Serpentine hands come in 4 to 10 inch dial diameters. These fit most German movements in existence. The minute hand has a 2.2mm square mounting hole, the hour hand has a 4.5mm round hole.

CH3Hands: $8.00$20.00
View Product

German Regulator Style

Hands For Mechanical Clocks

These fit most German mechanical clock movements. The minute hand has a 2.2mm square mounting hole, the hour hand has a 4.5mm round hole.

CH8: $18.00
View Product

German Spade Variant

Clock Hands

Hands for German mechanical clocks such as Hermle, Urgos or Kieninger. These hands are for a dial that is 6 inch (15cm) to 6 1/2 inch (17cm) wide from outside the numeral 3 to outside the numeral 9.

RC30: $15.00

American Mechanical

American Mechanical hands for Seth Thomas, Sessions, Ansonia, Gilbert, Bristol, Ingram, Welch, New Haven and others. These are for American made mechanical movements produced prior to the end of WW2 because they did not produce many clocks after this time. The hands come in a couple minute hand mounting styles such as Oblong or Square. The hour hand just has a round hole every time.

The further back in time one goes with USA antiques movements there was less mass production. This means the older the clock the weirder things can get. So these hands are not going to fit every clock that is old and from America but they do cover the mass productions instead. Sometimes is it required for the older antiques to make something work from what is available. Such as soldering two hands together to make one good one that fits or filing a hole bigger with a needle file.

Pierced Spade

Pierced Spade American Clock Hands

For 5 inch dial diameter. Choose square or oblong hole in the minute hand. For American antique movements. (Seth Thomas, New Haven, Ansonia, Gilbert, Waterbury and so on)

CH7: $10.00
View Product

Seth Thomas

ST Style American Clock Hands

For American antique movements. (Seth Thomas, New Haven, Ansonia, Gilbert, Waterbury and so on) This has a square hole in the minute hand.

CH10: $10.00
View Product

Spade Hands

American Spade Mechanical Clock Hands

For American antique movements. (Seth Thomas, New Haven, Ansonia, Gilbert, Waterbury and so on). Specify if the hole in the minute hand is oblong or square. Measurement is the dial diameter

CH9: $10.00
View Product

Maltese

American Maltese Mechanical Clock Hands

For American antique movements. (Seth Thomas, New Haven, Ansonia, Gilbert, Waterbury and so on) Specify if the hole in the minute hand is oblong or square. Measurement is the dial diameter

CH11: $10.00
View Product

Mechanical Seconds

Second Hand

Clock Hands

Second hand sweep for a mechanical floor clock with the second hand option. Please choose the movement number that is on the back plate of the brass movement itself for the correct second hand to be shipped.

CH13A: $10.00
View Product



All Clock Hands

Showing 1–16 of 33 results

  • launch

    View Product

    View more

    turned_in_out 4 3/4 Inch (121mm)

    Spade Quartz Clock Hands #H2

    The hands are sold as a pair. Only the minute hand is measured from the center of the mounting hole to the end. The minute hand has an oblong mounting hole, the hour hand has a round one.

    H2: $1.00$5.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 4 11/16 Inch (119mm)

    Serpentine Quartz Clock Hands #H1

    Serpentine quartz clock hands will fit the time only clock movement from clockworks. The hour hand will have a round hole, and the minute hand will have an oblong hole.

    H1: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 17 3/4 Inch (451mm)

    Spade Super-Torque Clock Hands

    Spade super-torque quartz clock hands will only work on a super torque C cell movement. The measurement is done with the minute hand only but the hour hand will come with the set.

    HTH3: $13.00$15.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Quartz Clock Hands

    Quartz Clock Second Hand

    Second hands for quartz clock movements that take a battery. The second hands come in Black / Gold / or Red. They are measured from the mounting post to the end of the long side pointer of the hand.

    SH3: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 3 5/8 Inch (92mm)

    Tapered Quartz Clock Hands #H4

    Tapered quartz clock hands for the time only units sold by Clockworks. The minute hand will have an oblong mounting hole and the hour hand is a round hole.

    H4: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Quartz Clock Hands

    Quartz Clock Movement Second-Hand

    Second hands for quartz clock movements that take a battery. The second hands come in Black / Gold / or Red. They are measured from the mounting post to the end of the long side pointer of the hand.

    SH1: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Quartz Clock Hands

    Battery Clock Second Hand

    Second hands for quartz clock movements that take a battery. The second hands come in Black / Gold / or Red. They are measured from the mounting post to the end of the long side pointer of the hand.

    SH2: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 2 3/4 Inch (70mm)

    Diamond-shaped Quartz Clock Hands #H8

    Diamond-shaped quartz clock hands fit battery clock movements purchased from Clockworks. Minute hand has an oblong mounting hole whereas the hour hand has a round one.

    h8: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 4 1/8 Inch (105mm)

    Straight Quartz Clock Hands #H6

    Straight quartz clock hands for the standard "I" shaft battery clock movements. These will fit any battery movement sold by Clockworks.

    H6: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 17.5 Inch (444mm)

    Tapered Super-Torque Clock Hands 17 1/2″

    Tapered super-torque quartz clock hands will only work on a super torque C cell movement. These are wide at the base and narrows down to a point. The measurement is done with the minute hand only but the hour hand will come with the set.

    HTH1: $13.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 3 3/8 Inch (85mm)

    Flat-Tapered Quartz Clock Hands #H5

    Flat-Tapered quartz clock hands for time only clock movements sold by Clockworks. An hour hand with a round mounting hole for a friction fit.

    H5: $1.00$10.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 2 1/2 Inch (63mm)

    Fancy Quartz Clock Hands #H9

    Fancy quartz clock hands for the standard "I" shaft battery clock movements. Basically if it takes a battery and you got it from clockworks.com, these will fit. We only carry the "I" shaft units.

    H9: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out German Mechanical Clock Hands

    Serpentine Mechanical Clock Hands

    This is a set of Serpentine Mechanical Clock Hands that fit most German mechanical clock movements made after 1950. The hands are measured by the time track diameter. A time track is the small ring outside of the numerals.

    CH3Hands: $8.00$20.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 2 1/2 Inch (63mm)

    Crescent-Moon Quartz Clock Hands #H10

    Crescent-Moon quartz clock hands for the standard "I" shaft battery clock movements. Basically if it takes a battery and you got it from clockworks.com, these will fit. We only carry the "I" shaft units.

    H10: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 2 3/4 Inch (76mm)

    Maltese Quartz Clock Hands #H3

    Maltese quartz clock hands have a nice design that falls between the Serpentine look and Spade. The hour hand is a friction fit and the minute hand mounts with its oblong mounting hole and a nut.

    H3: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 2 3/8 Inch (60mm)

    Wiggle Quartz Clock Hands #H11

    Wiggle quartz clock hands for the standard "I" shaft battery clock movements. Basically if it takes a battery and you got it from clockworks.com, these will fit.

    H11: $1.00
    View Product