Hardware for Clocks

Showing 17–32 of 72 results

• turned_in_out Hardware for Clocks

  Clock Clicks Wires Rivets

  The wires are preinstalled on the 6 clicks along with 6 rivets to install them on the clock. Used on many American 8 day time and strike spring driven movements. When winding a spring driven clock one can hear the clicking noise from the ratchet wheel.

  CP27: $10.00

  Clock Clicks Wires Rivets quantity

  ADD TO CART

• turned_in_out Hardware for Clocks

  Clock Count Wheel Clips

  Three pack of count wheel clips for American made mechanical clocks. These clips hold the count wheel to the main wheel on a Antique time and strike clock movement.

  CP31: $5.00

  Clock Count Wheel Clips quantity

  ADD TO CART

• turned_in_out Hardware for Clocks

  Clock Dial Key Grommets

  Three winding hole key grommets 3pk to be used on a clock dial with a 3/8 wide hole. They are to be installed on the dial after drilling out the winding arbor holes.

  CP32: $5.00

  Clock Dial Key Grommets quantity

  ADD TO CART

• turned_in_out Cuckoo Clock Parts

  Clock E-Style Clip Washers

  Split Clock E-Style clip Washers are similar to C clips as they attach various parts to the movement. These E-style clip washers get lost frequently as they are small and tend to fly off when removed.

  CP17: $12.00

  Clock E-Style Clip Washers quantity

  ADD TO CART

• turned_in_out Hardware for Clocks

  Clock Hand Washer Assortment

  100 Assorted mixed clock hand washers used on antique wall and mantle clocks. These go on top the minute hand on some clocks to maintain tension so the hand does not move around.

  CP7: $12.00

  Clock Hand Washer Assortment quantity

  ADD TO CART

• turned_in_out Hardware for Clocks

  Clock Hex Nut Assortment

  This is an assortment of 100 various sizes of clock hex nuts that are common in clock repair. These hex nuts fit many of the common antique American time and strike mechanical clock movements.

  CP18: $10.00

  Clock Hex Nut Assortment quantity

  ADD TO CART

• turned_in_out Hardware for Clocks

  Clock Machine Style Screws

  Smaller machine style screw assortment that comes in a pack of 50. It is not always easy to find the right screw so this is an assortment of sizes that may work. Machine style clock screws that may fit a variety of clocks produced in the 1900's.

  CP21: $12.00

  Clock Machine Style Screws quantity

  ADD TO CART

• turned_in_out Case / Mounting Parts

  Clock Movement Bar Mounts set of 4

  Clock movement bar mounts are flat stainless steel stock that mounts to the back of the clock movement. This allows you to have a unit that mounts in the rear. The nut comes off the pillar of the movement (one at a time so it does not disassemble). Then put this on the post, and lock it on with the... View Product

  RC22: $15.00

  Clock Movement Bar Mounts set of 4 quantity

  ADD TO CART

• turned_in_out Case / Mounting Parts

  Clock Movement Mounting Brackets Dog-Ear Style

  Set of four dog ear shaped clock movement mounting brackets. These go onto the outer movement posts under the hex nut on each corner. By installing only one corner at a time the movement with its gears never come apart.

  CP29: $13.00

  Clock Movement Mounting Brackets Dog-Ear Style quantity

  ADD TO CART

• turned_in_out Case / Mounting Parts

  Clock Movement Seat-Board Screws

  Clock Movement Seat-Board Screws are for modern German floor clock models that have a seat-board. The rectangle washer goes under the seat-board and the screw goes up through it and into the movement posts. Sold as a pair of washers and 1 3/4 inch long screws.

  CP28: $15.00 - $25.00

  View Product

• turned_in_out Hardware for Clocks

  Clock Parts Chime Hammer

  The chime hammers are the clock parts that strike the chime rods. These hammers come in three sizes which are the approximate length of the hammer from the tip to the screw and are available in nylon or leather. Also available are just the tips themselves in nylon.

  CP1: $1.00 - $10.00

  View Product

• turned_in_out Suspension Springs

  Clock Pendulum Suspension-Springs Assortment

  Sold in a 3 pack of 3 sizes. By and large, this suspension spring style is the most common spring for clocks made in Germany post 1950.

  sus-a-bundle: $12.00 – $30.00

  View Product

• turned_in_out Hardware for Clocks

  Clock Repair Brass Rivets

  An assortment of 100 brass rivets used in clock repair. These clock rivets come in a variety of sizes.

  Rivets: $15.00

  Clock Repair Brass Rivets quantity

  ADD TO CART

• turned_in_out Hardware for Clocks

  Clock Repair Bushing Assortment

  Clock Repair Bushing Assortment are solid brass bushings in a pack of 100. The assortment has a mix of outside and inside diameters. Use bushings when the pivot holes become oblong instead of round. These bushings are for bushing a clock movement by hand.

  CP20: $18.00

  Clock Repair Bushing Assortment quantity

  ADD TO CART

• turned_in_out Hardware for Clocks

  Clock Repair Hairspring Assortment

  Assortment of 72 clock hairsprings with there collets used in clock repair. Used often on mechanical alarm clock movements and other desk clocks. There are various sized springs and collet diameters in the center.

  CP22: $30.00

  Clock Repair Hairspring Assortment quantity

  ADD TO CART

• turned_in_out Hardware for Clocks

  Clock Repair Tapered Pins

  Used in clock repair these tapered pins come in an assortment of 50 sizes and diameters. These Clock Parts have many uses in clock repair. For example, they attach some dials, movement plates, suspensions and sometimes hands on the clock.

  CP2: $20.00

  Clock Repair Tapered Pins quantity

  ADD TO CART