All Products

Showing 33–48 of 650 results

  • launch

    View Product

    View more

    turned_in_out German Mechanical Clock Hands

    Serpentine Mechanical Clock Hands

    This is a set of Serpentine Mechanical Clock Hands that fit most German mechanical clock movements made after 1950. The hands are measured by the time track diameter. A time track is the small ring outside of the numerals.

    CH3Hands: $9.00$20.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 2 1/2 Inch (63mm)

    Fancy Quartz Clock Hands #H9

    Fancy quartz clock hands for the standard "I" shaft battery clock movements. Basically if it takes a battery and you got it from clockworks.com, these will fit. We only carry the "I" shaft units.

    H9: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Round Quartz Clock Inserts

    Clock Insert For 1-3/8-Hole #F1

    Clock insert #F1 is a round friction fit clock that is 1 7/16 (37mm) wide. It fits snug in a 1 3/8 (35mm) hole, with an overall depth of 3/8 (10mm). [bulk-discount-shortcode sku="F1"]

    F1: $14.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Cuckoo Clock Parts

    Cuckoo Clock Weights

    Cuckoo clock weights are in the form of pine cones. They are sold in gram weight and this gram amount is usually stamped on the weight itself. Cuckoo clocks all take the same weight for all the chains with only a few exceptions.

    CU5: $15.00$35.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Round Convex Clock Glass

    Round convex clock glass gets measured from one side to the other, the overall width. When working with a clock bezel it is important to order the right sized clock glass. If the glass is too narrow it will fall out the front of the bezel.

    BZ2: $8.00$70.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 17.5 Inch (444mm)

    Tapered Super-Torque Clock Hands 17 1/2″

    Tapered super-torque quartz clock hands will only work on a super torque C cell movement. These are wide at the base and narrows down to a point. The measurement is done with the minute hand only but the hour hand will come with the set.

    HTH1: $13.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Chiming Pendulum Quartz Clock Movements

    #QU22 Chiming Pendulum Clock Movement

    Takane Westminster chiming quartz clock movement. This movement is simple in design and to use. There is not a lot of options to figure out and costs less also. The chime is the electronic type and comes out of a built in speaker. So no speaker to mount, not many settings, simple economical compact and effective. The clock hands and... View Product

    QU22P: $40.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Weight Driven Movements

    Clock Repair Service or Customization

    Clockworks.com has 3 full time clock makers on staff. James Stoudenmire (Has 30 years experience with clocks), Bill (Has 15 years experience with clocks), and Bobby (Has 7 years experience with clocks). Part time we have Robert Tonkin (Has 70 years experience with clocks) Between our precision tools and our 100+ years of combined experience we can perform the best... View Product

    REPAIR: $15.00$1,500.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Clock Repair Tools

    Clock Mainspring Clamps 4PC

    Comes in a set of 4 to keep a mainspring in the wound position. This keeps them under control while replacing them in the movement or barrel. Best to get two of these sets for paired sized mainsprings.

    CT2: $10.00
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Pendulum Suspension Spring Rods

    Frequently needed pendulum suspension spring rods in 17 inch lengths. These suspension rods are cut, bent, and modified as needed for the pendulum to hang onto the clock. They replace the pendulum suspension rods that have worn out and has the spring steel broken.

    LSUS-C: $10.00
  • launch

    View Product

    View more

    turned_in_out Clock Repair Tools

    Clock Hand Puller Tool

    Remove stubborn hands and gears from a mechanical clock movement. The two jaw grab onto both sides of the hand or gear so it can be pulled off straight. This puller is 7/8 inch wide by about 1 1/2 inches tall.

    CU30: $10.00
  • launch

    View Product

    View more

    turned_in_out Hardware for Clocks

    Clock Dial Key Grommets

    Three winding hole key grommets to be used on a clock dial with a 3/8 wide hole. They are to be installed on the dial after drilling out the winding arbor holes.

    CP32: $5.00
  • launch

    View Product

    View more

    turned_in_out Square Clock Dials

    Heavy Paper Clock Dial

    Select Arabic or Roman Numerals, White or Ivory. Measurements are from outside the numeral on one side to outside the numeral on the other side. This would be the time track diameter and this is the ring that travels around the outside of the numerals.

    PDIAL1: $1.00$6.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Cuckoo Clock Parts

    Replacement Cuckoo Clock Chain

      These chains are sold in single 6FT lengths and come in various links per foot (LPF). The two ways of determining the correct chain is as follows. Count the LPF in the existing chain to match up. Or go by who made the clock movement instead.

    CU8: $10.00$18.00
    View Product
  • launch

    View Product

    View more

    turned_in_out 2 1/2 Inch (63mm)

    Crescent-Moon Quartz Clock Hands #H10

    Crescent-Moon quartz clock hands for the standard "I" shaft battery clock movements. Basically if it takes a battery and you got it from clockworks.com, these will fit. We only carry the "I" shaft units.

    H10: $1.00
    View Product
  • launch

    View Product

    View more

    turned_in_out Clock Repair Tools

    Mechanical Clock Bubble Level

    A simple yet practical level to help put a mechanical clock into beat or just level it for an even tick tock.

    CT33: $5.00