AA Cell High Torque Clock Movement #HT1

September 19, 2018 11:36 am Published by Leave your thoughts

$14.89

Attn: The hands for these units will be offered during the checkout process upon hitting the add to cart button.

The AA high torque quartz clock movements are much stronger than the low torque models.

They have a threaded post diameter of 5/16 and a case dimension of 2 1/8 x 2 1/8 x 1/2D.

The long hands for these movements are sold separately.

Minimum units Price/unit
1 $14.89
5 $12.89
12 $10.89
50 $8.89
100 $6.89
Clear
Bulk discount available
Continuous Sweep Time Only Quartz Clock Movement

When replacing, you will need to measure the post on the old unit, so you can match it up with your new chiming quartz movement. The post is the part that goes through the dial (face) and mounts from the front.

Clock Dial

Continuous Sweep Time Only Quartz Clock Movement

Dial Thickness

  • 1/16 inch thick
  • 3/16 inch thick
  • 5/16 inch thick
  • 9/16 inch thick
  • 3/4 inch thick

Size Post Needed

  • 3/16"
  • 5/16"
  • 7/16"
  • 11/16"
  • 15/16"

Removing a Bad Unit

The first step to replacing a quartz movement, is to be able to get to the movement from the back and also the front where the hands are.

1. Getting to the dial There are many case designs and styles and there is no telling what way you're clock case is made to get to the dial (face) of the clock. Sometimes it is very easy to get to the dial and hands, other times the dial is covered with glass and may require you to figure out how the clock case was put together, so you can take it apart enough to get to the dial. You may have to remove some screws, or if there is a bezel it maybe required to bend the bezel tabs some to get it off. Once you're at the point where you can remove the hands and also the back of the quartz unit, you're good to start replacing the unit.

2. Removing the hands If there is a second hand on the clock, it only needs to be grabbed with the thumb nails and pulled straight off of the clock to take it off.

Read More »

There are two styles to the minute hand, the kind that has the nut holding it down and the kind that is only on by friction fit with a round hole in the hand. The friction fit with no nut style just pulls straight off like the second hand did. The other style (the kind we sell) has the nut on the top of the minute hand to hold it down. To take this off, hold the minute hand still as you turn the nut to the left with needle nose pliers to loosen the nut so you can take it off with you're fingers. Next is the hour hand, this is only a friction fit with a round hole in the hand, the tube its on is tapered fatter as it goes down into the movement. Just twist the hand and pull it toward you until it comes off.

3. Removing the hex nut Then you will see a hex nut (six sided nut). use the same needle nose pliers to just turn the hex nut some to the left so it can be unscrewed with the fingers. With the hex nut removed the quartz clock movement will just fall out of the back side of the dial (face).

Clock Dial Dial = The clock face that the movements post goes through. Clock Dial Post = Threaded portion on the movement that takes the hex nut. Clock Dial Hex Nut = A six sided nut that threads onto the movement post.
Clock Dial Hanger = Included, but optional, steel part to hang clock. Clock Dial Hands = AKA needles, arms, pointers. Indicates hour and minute. Clock Dial Second Hand = The optional skinny pointer that ticks out the seconds.

Quartz Movement Assembly

These are the assembly instructions for the time only quartz clock movement into the clock case.
  1. Place hanger on post (optional)
  2. Place black washer on post (optional)
  3. Put post through the clock dial face
  4. Slide the brass washer onto the post of the movement that is sticking out of the clock dial face
  5. Put hex nut on post and tighten to hold movement to the back of the clock face – you may use needle nose pliers to get a tighter fit, however do not crank it down so tight that it ruins the clock face.
Read More »
  1. Push hour hand on the post (smaller of the 2 hands with round hole). This is a friction fit and should be pushed all the way down on the post without it touching the clock face.
  2. Put the minute hand on the post
  3. If using a second hand, skip to step 9. If you are not using a second hand, screw the cap nut on. You are done.
  4. If using a second hand, screw the small donut on top of minute hand and then push the second hand onto the pin in the center of the unit. You are done installing you're brand new quartz clock movement !

Clock Dial


AA Battery High Torque #HT1 Attn: The hands for these units will be offered during the checkout process upon hitting the add to cart button. The AA high torque quartz clock movements are much stronger than the low torque models. They have a threaded post diameter of 5/16 and a case dimension of 2 1/8 x 2 1/8 x 1/2D. The long hands for these movements are sold separately.

Commonly bought with..

  • Howard Miller Style High Torque Clock Hands Long High Torque Clock Hands #HTH7
    High Torque hands are long hands that need to go on a high torque battery operated clock movement. The hands have the USA standard 'I' shaft mounting hole in the minute hand. What this means is the hour hand will have a round mounting hole and the minute hand will have an oblong hole. These hands are sold as a pair, and measured by the minute hand only from the center of the mounting hole to the end of the pointer ...

    Clear

    HTH7: $6.89$9.89

  • Long High Torque Clock Hands #HTH1 Long High Torque Clock Hands #HTH1
    High Torque hands are long hands that need to go on a high torque battery operated clock movement. The hands have the USA standard 'I' shaft mounting hole in the minute hand. What this means is the hour hand will have a round mounting hole and the minute hand will have an oblong hole. These hands are sold as a pair, and measured by the minute hand only from the center of the mounting hole to the end of the pointer ...

    Clear

    HTH1: $2.89$12.89

  • Long High Torque Clock Hands #HTH8 Long High Torque Clock Hands #HTH8
    High Torque hands are long hands that need to go on a high torque battery operated clock movement. The hands have the USA standard 'I' shaft mounting hole in the minute hand. What this means is the hour hand will have a round mounting hole and the minute hand will have an oblong hole. These hands are sold as a pair, and measured by the minute hand only from the center of the mounting hole to the end of the pointer si...

    Clear

    HTH8: $8.89

  • Long High Torque Clock Hands #HTH3 Long High Torque Clock Hands #HTH3
    Attn: The high torque clock movement that is required to run these hands are offered during the check out process. If you hit the add to cart button they will show up. High Torque hands are long hands that need to go on a high torque battery operated clock movement. The hands have the USA standard 'I' shaft mounting hole in the minute hand. What this means is the hour hand will have a round mounting hole and the...

    Clear

    HTH3: $1.89$14.89

Additional information

Weight 0.2 lbs
Post Length

3/16" Post for 1/16" Thick Dials, 5/16" Post for 3/16" Thick Dials, 9/16" Post for 7/16" Thick Dials, 11/16" Post for 9/16" Thick Dials, 13/16" Post for 11/16" Thick Dials, 15/16" Post for 13/16" Thick Dials, 7/16" Post for 5/16" Thick Dials

Comparable products…

  • Chiming quartz clock movement with the best sound by clockworks.com #QU40 Chime Pendulum Clock Movement
    When replacing, you will need to measure the post on the old unit, so you can match it up with your new chiming quartz movement. The post is the part that goes through the dial (face) and mounts from the front. Chiming Quartz Clock Movements Assistance = 800-381-7458 Dial Thickness 1/16 inch thick 3/16 inch thick...

    Clear

    QU40P: $59.89