Shop

Showing 65–80 of 1025 results

• turned_in_out Cuckoo Clock Parts

  Cuckoo Bellow Top Epoxy Adhesive

  Cuckoo bellow tops use epoxy when replacing a worn top with a new one. The epoxy also works well to glue broken cuckoo wood case parts back together.

  CU27: $6.00

  Cuckoo Bellow Top Epoxy Adhesive quantity

  ADD TO CART

• turned_in_out Mainsprings

  Loop End Clock Mainspring

  First, measure the width. Then match it up with the proper section of the chart. After matching the width, see what is the closest spring in that section in thickness and length.

  LESPRING: $15.00 – $50.00

  View Product

• turned_in_out Oiling and Cleaning

  Brass Bristle Clock Cleaning Brush

  Brush, with wooden handle, for cleaning clocks. Behold this beautiful brass bristle brush which brings beauty to big bulky brass. Use this on stubborn spots of grime, along with cleaning solution.

  CL15: $8.00

  Brass Bristle Clock Cleaning Brush quantity

  ADD TO CART

• turned_in_out Pendulum Sticks

  Hermle wood-stick clock pendulum

  The CM number off of the Hermle clock movement itself is required to get the right pendulum. This information is not on the paper work and not on the wood case, it is only on the back of the movement.

  H-WS-PEND: $36.00 – $114.00

  View Product

• turned_in_out All Products

  Hermle Quartz Movement Replacement

  Replacement movements for the German made Hermle quartz, . These chiming units take two C-cell batteries and play two different songs. Well made quartz movements that last for a long time. The old units seem to give up the ghost during daylight savings when they do die.

  MSO: $80.00

  View Product

• turned_in_out German Mechanical Clock Hands

  Mechanical Clock Spade Hands

  Spade hands that fit most German mechanical clock movements. The hands are measured by the time track diameter. A time track is the small ring outside of the numerals and the minute hand length will be about half this diameter.

  CH1: $20.00 – $26.00

  View Product

• turned_in_out Super Long Clock Hands

  Taper Super-Torque Clock Hands 17 3/4″

  Tapered super-torque quartz clock hands will only work on a super torque C cell movement. These are wide at the base and narrows down to a point. The measurement is done with the minute hand only but the hour hand will come with the set.

  HTH1: $13.00

  View Product

• turned_in_out Clock Keys and Cranks

  Double Ended Clock Key 6pk

  Key size are often confusing enough on the single end styles before adding another end to the confusion. offering a 6 pack of steel double end keys that are the most common combination of sizes. One end of the key will wind the clock.

  CK2: $50.00 $45.00

  View Product

• turned_in_out Clock Repair Tools

  Clock Let Down Tool Set of 4

  The let down tools set comes with a handle and 3 chucks that fits just about every winder arbor size. Put the chuck into the handle and then release the mainspring slowly with the hand grip.

  CT25: $50.00

  Clock Let Down Tool Set of 4 quantity

  ADD TO CART

• turned_in_out Clock Weight Accessories

  Polished Clock Weight Cap

  Polished brass tone weight shell end caps are the tops and bottom of the weight shell. Available in 43mm, 47mm or 60mm diameters and sold individually.

  WE1: $8.00 – $12.00

  View Product

• turned_in_out Round Clock Dials

  Round Ivory Clock Dial

  Round ivory clock dial in either Arabic or Roman numerals. Please remember to remove the protective plastic coating from the Round gold clock dial before use. The sized listed below are the overall width from side to side.

  RD3: $5.00 – $20.00

  View Product

• turned_in_out Hardware for Clocks

  American Clock Hand Nuts

  A mixture of steel and brass American clock hand nuts. This is a 12 pack of hand nuts that are all the same thread size. They are likely to fit American time strike units made from around 1930 to 1950's.

  CP14: $15.00

  American Clock Hand Nuts quantity

  ADD TO CART

• turned_in_out Cuckoo Clock Parts

  Cuckoo Clock Deer Antlers

  Cuckoo clock deer antlers made of sturdy plastic with a wooden look. These plastic antlers will not break as easy as the old wooden antlers.

  CU7: $12.00 – $19.20

  View Product

• turned_in_out Clock Tools

  Clock Movement Assembly Posts

  These Clock Movement Assembly Posts keep the movement plate flat. This makes for a workable platform to use during reassembly.

  CT10: $50.00

  Clock Movement Assembly Posts quantity

  ADD TO CART

• turned_in_out Chain Driven Movements

  451-050 Hermle Clock Movement

  The Hermle clock movement 451-050 or 451-050H is a Westminster Chime unit with 8 hammers on the back. This high quality German movement comes oiled and includes its leader, suspension spring and hand nut.

  451-050: $375.00

  View Product

• turned_in_out Chiming Pendulum Quartz Clock Movements

  Quartz Chime Clock Movement #QU22

  Reliable and durable this chiming quartz clock movement is made by Takane. Simplistic in its functions and works as a good replacement for many quartz clock movements. 3″ x 4 3/4″ x 1 1/4″

  QU22P-B:

  View Product