Hermle 341-340 Clock Movement Mounting Brackets

September 19, 2018 3:37 pm Published by Leave your thoughts

$19.89

Clock Movement Mounting Brackets set of 2. This is for a front mounting a Hermle 341 or 340 series clock movement. Do not remove all four hex nuts on the movement plates at once or it will come disassembled. Just take off the hex nuts on one side at a time, take of the two hex nuts, put this on the threads, put the hex nuts back on. Do this for the other side also and your done, you can mount your movement to the front of the wood clock case. These measure 4 3/4 inch (121mm) long and are to mount the German made Hermle 341 or 340 series clock movement.

In stock

Clock Movement Mounting Brackets set of 2. This is for a front mounting a Hermle 341 or 340 series clock movement. Do not remove all four hex nuts on the movement plates at once or it will come disassembled. Just take off the hex nuts on one side at a time, take of the two hex nuts, put this on the threads, put the hex nuts back on. Do this for the other side also and your done, you can mount your movement to the front of the wood clock case. These measure 4 3/4 inch (121mm) long and are to mount the German made Hermle 341 or 340 series clock movement.

Additional information

Weight 0.5 lbs

Comparable products…

  • Clock Pendulum Nut Assortment Clock Pendulum Nut Assortment
    Pendulum Nuts Pendulum nut assortment of 6 for floor clocks and wall clocks. Turning the nut so to raise the bob will speed up the clocks time, lowering the bob will slow the clocks time....

    CP8: $14.89

  • Clock Repair Movement Assembley Post Set Clock Repair Movement Assembley Post Set
    Keeps the movement up and stable during an overhaul. Just tighten one post on each corner to work on the clock movement as its in the air. Set of 4 posts 2 3/4' long. Includes a hanging bracket to hang the movement for wwwing ...

    CT10: $24.89

  • Clock Repair Large Cutting Broach Set Clock Repair Large Cutting Broach Set
    The cutting broach is the tool that is used to ream out a pivot hole to accept a bushing. The hole gets reamed larger to be able to install the new round bushing. Also to increase a bushing hole diameter as well. Comes in two sized sets, the smaller one is used for alarm clocks or large pocket watches....

    CT11: $34.89

  • Clock Loop End Mainspring Winder Tool Clock Loop End Mainspring Winder Tool
    Winder for loop end mainsprings, to be used with the mainspring clamps. This is to take a unwound loop end mainspring and wind it up to get a clamp on. When the C clamp is on, it is much easier to manage in the clock movement assembly process. There is no 'safe' operation on this one. It is both dangerous and tricky. You would use the great wheel, put it through the hole in the device, clamp it down with something...

    CT1: $14.89

  • German Hand Nuts German Hand Nuts
    German Hand Nuts 12 Assorted hand nuts for German movements. With this assortment of hand nuts you will get one for your German movement with no problem. However these hand nuts will not work on a cuckoo clock those are under cuckoo parts....

    CP9: $9.89

  • Small Springs For Clock Repair Small Springs For Clock Repair
    Small Springs Assortment of small springs that can be used with clocks. These are not made for clocks but are very useful to modify for clock repair....

    CP42: $4.89

  • Clock Clicks & Rivets Clock Clicks & Rivets
    Clicks & Rivets 50 Mixed sized clicks and rivets. Clicks hold the mainspring in the coiled position during and after winding the clock. Please use caution when working with mainsprings....

    CP5: $9.89

  • Clock Hand Washer Assortment Clock Hand Washer Assortment
    Clock Hand Washers 100 Assorted mixed clock hand washers. These go on top the minute hand on some clocks to maintain tension so the hand does not flop around. Item #CP7 $6...

    CP7: $9.89

  • Tall Case Pulley Tall Case Pulley
    Pulley for the tall case antique clock. This is useful for the cable driven antique clocks for the cable to loop through and the weight to hang on....

    CP41: $19.89

  • Clock Repair 7 Piece Closing Punches Clock Repair 7 Piece Closing Punches
    Punch set to make a oblong pivot hole round again instead of installing the bushing. The movement plates would be separated for the punch set to be used. ...

    CT12: $49.89

  • Clock Repair Centering Punch Clock Repair Centering Punch
    A centering punch is to punch an indent in metal stock so a drill will line up with the indent when drilling a hole. This has adjustment for a heavy or light punch for delicate or heavier use. ...

    CT13: $9.89

  • Bracket Clock Handle Bracket Clock Handle
    3 1/2 inch wide, 1 1/2 inch tall, solid brass Bracket Clock top handle. A Bracket clock is a square clock with a square dial, this is the handle that mounts to the top of the clock case. ...

    CP43: $29.89