Clock Chain by Movement Maker

September 19, 2018 11:38 am Published by Leave your thoughts

$5.89$24.89

Clock chain by movement maker. The chain is sold by LPF. Take a section of your old chain and count the links so it matches the LPF (links per foot) that are on the drop down menu below. Most one day cuckoo clocks take 61LPF. Many 8 day cuckoo clocks take 48LPF. All Hermle chain driven units take 46.5LPF.

Clear

Clock chain by movement maker. The chain is sold by LPF. Take a section of your old chain and count the links so it matches the LPF (links per foot) that are on the drop down menu below. Most one day cuckoo clocks take 61LPF. Many 8 day cuckoo clocks take 48LPF. All Hermle chain driven units take 46.5LPF.

Additional information

Weight 0.4 lbs
Size

38LPF 2.0mm 72in =Kieninger, 40LPF 1.8mm 60in =UW03, 43LPF 1.6mm 72in, 45LPF 1.6mm 60ins =Kieninger SK, 45LPF 1.4mm 72in =8 Day Hubert Herr, 46.5LPF 1.7mm 60in =Hermle and Urgos, 46.5LPF 1.7mm 60in Dark =Hermle and Urgos, 48LPF 1.2mm 78in =Regula 34, 48LPF 1.2mm 78in Dark Brass =Regula 34, 52LPF 1.05mm 70in Brass, 59LPF 09mm 78in Brass =1 Day Hubert Herr, 61LPF 0.9mm 70in Brass =Regula 25, 61LPF 0.9mm 70in Dark Brass =Regula 25, 66LPF 0.7mm 70in Brass, 72LPF 0.7mm 70in Brass

Comparable products…

  • Clock Hand Washer Assortment Clock Hand Washer Assortment
    Clock Hand Washers 100 Assorted mixed clock hand washers. These go on top the minute hand on some clocks to maintain tension so the hand does not flop around. Item #CP7 $6...

    CP7: $9.89

  • Clock Pendulum Nut Assortment Clock Pendulum Nut Assortment
    Pendulum Nuts Pendulum nut assortment of 6 for floor clocks and wall clocks. Turning the nut so to raise the bob will speed up the clocks time, lowering the bob will slow the clocks time....

    CP8: $14.89

  • Clock Repair Large Cutting Broach Set Clock Repair Large Cutting Broach Set
    The cutting broach is the tool that is used to ream out a pivot hole to accept a bushing. The hole gets reamed larger to be able to install the new round bushing. Also to increase a bushing hole diameter as well. Comes in two sized sets, the smaller one is used for alarm clocks or large pocket watches....

    CT11: $34.89

  • Small Springs For Clock Repair Small Springs For Clock Repair
    Small Springs Assortment of small springs that can be used with clocks. These are not made for clocks but are very useful to modify for clock repair....

    CP42: $4.89

  • Clock Loop End Mainspring Winder Tool Clock Loop End Mainspring Winder Tool
    Winder for loop end mainsprings, to be used with the mainspring clamps. This is to take a unwound loop end mainspring and wind it up to get a clamp on. When the C clamp is on, it is much easier to manage in the clock movement assembly process. There is no 'safe' operation on this one. It is both dangerous and tricky. You would use the great wheel, put it through the hole in the device, clamp it down with something...

    CT1: $14.89

  • Tall Case Pulley Tall Case Pulley
    Pulley for the tall case antique clock. This is useful for the cable driven antique clocks for the cable to loop through and the weight to hang on....

    CP41: $19.89

  • German Hand Nuts German Hand Nuts
    German Hand Nuts 12 Assorted hand nuts for German movements. With this assortment of hand nuts you will get one for your German movement with no problem. However these hand nuts will not work on a cuckoo clock those are under cuckoo parts....

    CP9: $9.89

  • Bracket Clock Handle Bracket Clock Handle
    3 1/2 inch wide, 1 1/2 inch tall, solid brass Bracket Clock top handle. A Bracket clock is a square clock with a square dial, this is the handle that mounts to the top of the clock case. ...

    CP43: $29.89

  • Clock Repair 7 Piece Closing Punches Clock Repair 7 Piece Closing Punches
    Punch set to make a oblong pivot hole round again instead of installing the bushing. The movement plates would be separated for the punch set to be used. ...

    CT12: $49.89

  • Clock Repair Movement Assembley Post Set Clock Repair Movement Assembley Post Set
    Keeps the movement up and stable during an overhaul. Just tighten one post on each corner to work on the clock movement as its in the air. Set of 4 posts 2 3/4' long. Includes a hanging bracket to hang the movement for wwwing ...

    CT10: $24.89

  • Clock Repair Centering Punch Clock Repair Centering Punch
    A centering punch is to punch an indent in metal stock so a drill will line up with the indent when drilling a hole. This has adjustment for a heavy or light punch for delicate or heavier use. ...

    CT13: $9.89

  • Clock Clicks & Rivets Clock Clicks & Rivets
    Clicks & Rivets 50 Mixed sized clicks and rivets. Clicks hold the mainspring in the coiled position during and after winding the clock. Please use caution when working with mainsprings....

    CP5: $9.89