Sale!
VOLFIX_QU22

Quartz Chime Clock Movement #QU22

(9 reviews)

Quartz Chime Clock Movement

Reliable and durable this chiming quartz clock movement is made by Takane. Simplistic in its functions and works as a good replacement for many quartz clock movements.

3″ x 4 3/4″ x 1 1/4″

Read more »
Bulk discount available

Hands and pendulum not included

In stock

Chiming quartz clock movement with the best sound by clockworks.comWhen replacing the QU22 Chiming Pendulum Clock Movement, measure the post on the old unit, then match it up with your new chiming quartz movement. The post is the part that goes through the dial (face) and mounts from the front.

Chiming Quartz Clock Movements

Assistance = 800-381-7458

Dial Thickness

  • 1/16 inch thick
  • 3/16 inch thick
  • 5/16 inch thick
  • 9/16 inch thick
  • 3/4 inch thick

Size Post Needed

  • 3/16"
  • 5/16"
  • 7/16"
  • 11/16"
  • 15/16"

Removing a Bad Unit

The first step to replacing a quartz movement, is to get to the movement from the back and also the front where the hands are. 1. Getting to the dial There are many case designs and styles and there is no telling what way you're clock case is made to get to the dial (face) of the clock. Sometimes it is very easy to get to the dial and hands. But other times glass covers the dial and you have to figure out how the clock case was put together. This is so you can take it apart enough to get to the dial. You may have to remove some screws, or, if there is a bezel, to bend the bezel tabs some to get it off. Once you're at the point where you can remove the hands and also the back of the quartz unit, you're good to start replacing the unit. 2. Removing the hands If there is a second hand on the clock, just grab it with your thumb nails and pull it straight off of the clock to remove it.

Hand styles

There are two styles to the minute hand. First is the kind that has the nut holding it down. Second is the kind that is only on by friction fit with a round hole in the hand. The friction fit with no nut style just pulls straight off like the second hand did.

The other style (the kind we sell) has the nut on the top of the minute hand to hold it down. To take this off, hold the minute hand still as you turn the nut to the left with needle nose pliers to loosen the nut so you can take it off with your fingers. Next is the hour hand. This is only a friction fit with a round hole in the hand, the tube its on tapers fatter as it goes down into the movement. Just twist the hand and pull it toward you until it comes off.

3. Removing the hex nut Then you will see a hex nut (six sided nut). Use the same needle nose pliers to just turn the hex nut to the left so you can unscrew it with your fingers. With the hex nut off, the quartz clock movement will just fall out of the back side of the dial (face).

Clock Dial Dial = The clock face that the movements post goes through. Clock Dial Post = Threaded portion on the movement that takes the hex nut. Clock Dial Hex Nut = A six side nut that threads onto the movement post.
Clock Dial Hanger = Included, but optional, steel part to hang clock. Clock Dial Hands = AKA needles, arms, pointers. Indicates hour and minute. Clock Dial Second Hand = The optional skinny pointer that ticks out the seconds.

Quartz Movement Assembly

These are the assembly instructions for the time only quartz clock movement into the clock case.
  1. Place hanger on post (optional)
  2. Place black washer on post (optional)
  3. Put post through the clock dial face
  4. Slide the brass washer onto the post of the movement that is sticking out of the clock dial face
  5. Put hex nut on post and tighten to hold movement to the back of the clock face – you may use needle nose pliers to get a tighter fit, however do not crank it down so tight that it ruins the clock face.
  6. Push hour hand on the post (smaller of the 2 hands with round hole). This is a friction fit and should push all the way down on the post without it touching the clock face.
  7. Put the minute hand on the post
  8. If using a second hand, skip to step 9. If you are not using a second hand, screw the cap nut on. You are done.
  9. If using a second hand, screw the small donut on top of minute hand and then push the second hand onto the pin in the center of the unit. You are done installing you're brand new quartz clock movement !

Clock Dial


Movement Description

Takane Westminster QU22 Chiming Pendulum Clock Movement. This movement is simple in design and to use. There is not a lot of options to figure out and costs less also. The chime is the electronic type and comes out of a built in speaker. So no speaker to mount, not many settings, simple economical compact and effective. The pendulum, clock hands and the second hand are sold separately.
The pendulum comes 16 inches at its longest point and the bob comes in three diameter options. These items do not come with the movement and are available for purchase separately.
  • 16 inch pendulum at longest
  • Westminster chime

QU22 Chiming Pendulum Clock Movement Notes

Movement

Takane made chiming quartz clock movement that plays Westminster on the quarter hour and then strikes out the hour at the top of the hour.

Sound

Westminster chime on the quarters and then strikes out the hours.

Hands

Any of the hands we sell for quartz clock movements will fit this unit. As far as the quartz units go, we only have the standard American “I” shaft units and hands. This means the hour hand will have a round hole and the minute hand would have a oblong hole. The hour hand goes on as a friction fit, then the minute hand goes on the upper post with its nut. You can use a second hand but it is optional. All hands are sold separately and are available here as well.

Pendulum

This movement supports a pendulum that is 16 inches at its longest. However you can shorten it to anything less than 16 inches with ease. The pendulum has three bob diameter options to choose from, the bob is the round disk at the bottom of the pendulum rod. Please note although this is a pendulum unit, it can be used with or without the pendulum. If you do not use the pendulum, it can just lock the pendulum swinger to one side and not use it. These items are sold separately.

Mounting Post

The movement has a post with threads and comes in three lengths. This is the fat part with the threads that takes the hex nut. This post length is what we measure, the actual part that the hands go onto sticks out another ¼ inch beyond this measurement, but we do not count that in the measurement. The post lengths available for this unit is either 5/16 long or 11/16 long. The posts are all 7/16 wide and this is wider then the typical ⅜ wide posts that are found on the market. Be sure the dial has a hole diameter of ½ inch wide for this to go through.

Features

    • Westminster and then strike out the hourly count
    • Second Hand Option
    • Pendulum Option
    • Takes one C Cell Battery

Instructions

  1. Insert a C cell battery into the movement.
  2. Make it chime the hours by turning the knob on the back
  3. Install the hands where the clock chimed.
How to make the clock chime on time. First we need to know if the clock chime is correct no matter what it says the chime is. We only need to have the hands point to where the clock thinks it is, or where its chiming in other words. And then set the clock to time. When the clock chimes, take the hands off of the clock and reposition them to match the number of chimes that you just heard. In other words if it chimes that it's 3 o'clock, put the hour hand to the three and the minute hand to the 12. Then set the clock to the correct time. IF the clock minute hand will not point exactly to the 12, do this. Find the circle spinning setting knob on the back of the movement and hold this still with your fingers so it will not move. At the same time you stop this from moving, point the minute hand to the 12 where it needs to point to when it chimes. Let go of both. [wcsp_cross_sell orderby="rand" order="ASC" product_num="4" display_columns="4" title="Need a hand??" product_id="377"]

Additional information

Weight0.5 lbs
Pendulum Bob Diameter

2 1/8 Inch, 2 3/4 Inch, 3 1/2 Inch, Non Pendulum

Threaded Post Length

5/16 Inch, 7/16 Inch, 11/16 Inch, 15/16 Inch

QU22 Chiming Pendulum Clock Movement

Weight0.2 lbs
Threaded Post Length

7/16 Inch, 11/16 Inch, 13/16 Inch

Pedulum Bob Diameter

2 1/8 Inch, 2 3/4 Inch, 3 1/2 Inch, Non Pendulum

Quartz Clock Pendulum

Weight0.5 lbs
DimensionsN/A
Size

2 1/8 inch (54mm), 2 3/4 inch (70mm), 3 1/2 (90mm)

Quartz Clock Movement Hardware

Weight0.1 lbs

Serpentine Quartz Hands #H1

Weight0.03 lbs
Minute Hand Length

1 1/8 Inch (29mm), 1 5/8 Inch (41mm), 1 3/4 Inch (44mm), 2 Inch (51mm), 2 7/16 (61.8mm), 3 Inch (76mm), 3 1/4 Inch (82.4mm), 4 1/8 Inch (102mm), 4 3/4 Inch (120.5mm), 5" (127mm), 6 1/4 Inch (159mm), 9 1/4 Inch (235mm)

Color

Black, Gold

Spade Quartz Clock Hands

Weight0.01 lbs
Minute Hand Length

1 11/16 Inch (42.9mm), 1 11/16 Inch (42.9mm), 2 Inch (51mm), 2 1/2 Inch (64mm), 2 3/16 (55.6mm), 2 3/16 (55.6mm), 2 7/8 Inch (73.0mm), 3 Inch (76.2mm), 3 3/8 Inch (85mm), 3 11/16 Inch (93.7mm), 3 11/16 Inch (93.7mm), 4 1/16 Inch (103.2mm), 4 3/8 Inch (111.1mm), 4 3/8 Inch (111.1mm), 4 3/4 Inch (121mm), 5 Inch (127mm), 5 1/2 Inch (140mm), 5 3/4 Inch (146mm), 5 5/16 Inch (134.9mm), 5 5/16 Inch (134.9mm), 6 7/8 Inch (175mm), 6 3/4 Inch (171mm), 8 3/4 Inch (222mm), 8 3/4 Inch (222mm)

Color

Black, Gold

Maltese Quartz Clock Hands #H3

Weight0.01 lbs
Minute Hand Length

1 3/4 Inch (44mm), 2 1/16 Inch (52mm), 2 3/4 Inch (76mm)

Color

Black, Gold

Tapered Quartz Clock Hands #H4

Weight0.01 lbs
Minute Hand Length

1 1/2 Inch (38mm), 1 7/8 Inch (47mm), 2 1/4 Inch (57mm), 3 3/16 Inch (81mm), 3 5/16 Inch (84mm), 3 5/8 Inch (92mm), 11 Inch (279mm), 17 1/2 Inch (444mm)

Color

Black, Gold

Quartz Clock Movement Second-Hand

Weight0.01 lbs
Length

1 1/2 Inch (38mm), 1 3/4 Inch (44mm), 2 1/2 Inch (64mm)

Color

Gold, Red, Black

Second Hands for Battery-clocks

Weight0.01 lbs
Length

2 3/4 Inch (70mm)

Color

Red, Black, Gold

Quartz Clock Second Hand

Weight0.01 lbs
Length

1 3/4 Inch (44mm), 2 1/8 Inch (54mm), 2 7/8 Inch (73mm), 3 5/8 Inch (92mm), 4 Inch (102mm), 4 3/8 Inch (111mm), 4 3/4 Inch (121mm), 5 Inch (133mm)

Color

Gold, Red, Black

16
Ask a Clock Question

Subscribe
Notify of
guest

newest
oldest most voted
Inline Feedbacks
View all comments
Robert j Walsh
Robert j Walsh
1 month ago

On the QU22 clock moverment can the sound be adjust louder?

James Stoudenmire
Admin
1 month ago
Reply to  Robert j Walsh

No not on that one

James Stoudenmire
40yr Clockmaker
Author of Clockworks.com

John B
John B
5 months ago

I have this unit but the chime does not work. Can just the chime be fixed without replacing the whole movement?

James Stoudenmire
Admin
5 months ago
Reply to  John B

Sometimes. See if the wires to the speaker need solder

James Stoudenmire
30yr Clockmaker
Author of Clockworks.com

Cindy
Cindy
7 months ago

How do I change the batteries?

James Stoudenmire
Admin
7 months ago
Reply to  Cindy

1. take the old one out
2. put the new one in the same direction as the old

Easy !

James Stoudenmire
30yr Clockmaker
Author of Clockworks.com

Carol Carroll
Carol Carroll
1 year ago

Chimes won’t chime

James Stoudenmire
Admin
1 year ago
Reply to  Carol Carroll

Sorry do hear this, please email us by replying to your receipt on this same issue and we will replace the unit no charge

​James Stoudenmire
30yr Clockmaker
Author of Clockworks.com

Peter Sybek
Peter Sybek
1 year ago
Rating :
     

Very nice product and great staff here, thank you clockworks.

booknook14779
booknook14779
2 years ago

Is there an adjustment for the volume

James Stoudenmire
Admin
2 years ago
Reply to  booknook14779

Sorry no, not on this unit. All the other chime units have it however, see this link
https://www.clockworks.com/product-category/clock-movements/battery-operated/chiming-pendulum-quartz-clock-movements

James

Bruce Belter
Bruce Belter
3 years ago

How do you oil clock movements on Howard Miller 612 697

James Stoudenmire
Admin
3 years ago
Reply to  Bruce Belter

Smallest drop of clock oil, where ever on thing rubs another.
https://www.clockworks.com/?post_type=product&s=Oil

James

James M. Dunlavy
James M. Dunlavy
3 years ago

I have a unit but it does not work any more. I have pendulum but I would like new hands. I have filled out post size (7/16) and hand size, but it will not go to cart. It tells me fill out more info. what else is needed?

James Stoudenmire
Admin
3 years ago

Hi

Not sure, seems fine on our end. Please give Debby a call on Monday, she is in the quartz department and can take the order. 800 381 7458

James

Thank you !

Anthony L Hauser
Anthony L Hauser
4 years ago

Were is the pendulum measured from to get its length?