The following are accessories that fit the quartz clock movements that Clockworks offers. There are many different types of quartz movements on the market, hence we specifically state these items are for the movements that we sell. Of course Clockworks encourages organizations to offer clock building as a fun project. Therefore, each product is available with bulk pricing for schools and other large orders. Please email the request for a quote on bulk purchases.
Quartz Clock Pendulum
Quartz clock pendulum that will work on any battery operated pendulum unit offered by Clockworks. A Quartz Clock Pendulum Bob is the round disk at the bottom of the quartz clock pendulum. In fact, these quartz pendulum bobs come in three different sizes to choose from. First, measure out the length of the rod that is appropriate for the clock. Then, slide it on the end of the pendulum rod.
This is a steel hanger for quartz clock movements. Thus, hang the clock on the wall by this steel hanger instead of by the clock case. Specifically, these hangers fit AA battery movements only. So simply install it by slipping it over the hand shaft post.
Quartz Clock Movement Hardware
Quartz clock movement hardware for time only clock movements that run by a battery. Of course all movements that Clockworks sells includes a hardware packet. However it is always good to have extras on hand in case a cap nut gets lost. So all hardware packs include a rubber washer, a brass washer, a hex nut, a doughnut, and a cap nut. Additionally, these hardware packs are for posts that have threads which are 5/16 in diameter only. In other words, it is what the hex nut will screw onto, the 5/16 wide post.
Clock Numerals - Dial Numbers
A versatile product for multiple types of clocks or craft projects. Use clock Numerals or dial numbers to replace missing ones on the clock dial. Additionally, use these numbers to create a clock dial out of whatever material the clock is to be made out of. Of course, it is always fun to be creative and incorporate these numerals in a variety of projects and not just clocks. In essence, these are sticky numbers that peel off and press on to whatever material the dial is made out of. However, Clockworks recommends using some more glue to secure them. The sticky back is not always sticky enough to hold them in place for a long time.
The best glue to use with these are the clear epoxy. So mix the glue and let it stand for about 5 minutes. Then it will be set as well as being clear. Furthermore, the brass numbers, in addition to the largest plastic numbers, do not stick on their own. Above all, remember to apply epoxy in order for them to stick to the dial. So either way, if using the self sticking or the non self sticking clock numerals the clear epoxy is a good idea for both.
These Numerals have a sticky back to them so they will mark the dial or wall when they come off.
Battery Quartz Clock Hands - Quartz clock hands in black and gold. Please choose the length by the minute hand only. - Clockworks
About Quartz Clock HandsDescriptionCompatibility CheckMeasuring and OrderingMounting
Sold as a pair with both hour and minute hands. Styles vary depending on length.
Quartz Clock Hands
Quartz Clock Hands that will fit any battery movement we offer. There are two types of quartz hands in the world. One is China standard and one is American standard. The China way of using the hands is with round holes in both the hour and minute hands.
Comparatively, the American style has an oblong mounting hole in the minute hand and a round hole for the hour hand that fits what is known as an "I" shaft. All of the hands offered here fit "I" shaft movements only. In other words all of them will fit the quartz movements that we sell.
Quartz clock hand compatibility
When replacing a quartz clock movement, the old hands may fit the new movement just fine. If there is an oblong hole in the minute hand, chances are good that it will fit.
The hour hand will fit the new quartz movement either way. To clarify, it is the minute hand (the longer of the two hands) that is a concern. In any event, if in doubt, it is best to order new hands for the new movement upon checking out. This way it will be all set and will have everything you need for a smooth movement swap out.
Measuring and Ordering New Hands
Quartz clock hands come together as a set, but you only measure the minute hand when replacing them. Measure it, the long hand, from the mounting hole to the tip. The shorter hand, the hour hand, comes with the minute hand and is proportionally smaller.
Quartz Clock Second HandsSecond Hand InstallationTo Tighten the handPerformance Options
Quartz Clock Second Hands
Second hands come in black, gold, or red. They are measured from the mounting post to the end. These will fit the AA battery units and also the Cell Super Torque units. However they do not come extremely long, and the C cell Super Torque is not made to run an extremely long second hands anyway. Only the hour and minute hands can be long on these units.
Second Hand Installation
Quartz clock second hands have a hollow tube to mount it on the movement. This hollow tube mounts onto the pin that is inside the tip of the movement. In other words, the mount is by friction fit onto the quartz clock movement. Install the second hand by placing the tube over the pin in the hand shaft and push down. If the hand cannot make the uphand swing from 6 o'clock to 12 o'clock on the dial, the tube may need tightening so the fit is tighter. Likewise, if the second hand just flops down as soon as it is on the pin, then tighten it in the same manner.
Second Hand Tightening
This is not the usual situation, but it does happen. The tube on the Quartz clock second hand is split so tightening it to achieve a better friction fit is easy. Squeeze the tube slightly with needle nose pliers and it will be tight again. Remount the hand as before and it should climb the hill no problem. Alternately, sometimes the tube will not go onto the pin at all because the tube split is too close. Open the tube slightly on the Quartz clock second Hand, or push a little harder, and it will go onto the pin.
There are two types of quartz movements that run these hands. The first type are step motion movements. Step motion movements have Quartz clock second hands that jump from one second to the next. Each second is visible because the second hand bounces as each second goes by. Even though the second hand bounces, they do not make a loud tick tock sound as one might think. In fact, most people say they cannot hear it at all unless their ear is right up against it. The second type are sweep motion movements. Sweep motion movements have a second hand that scrolls smoothly around the dial. There is no jumping of the hand as it goes around. The M7 battery units from Clockworks are continuous sweep, our Super Torque units are step motion.
Super Torque Clock Hands - "I" Shaft quartz clock hands for High Torque battery operated quartz clock movements. - Clockworks
High Torque HandsDescriptionHand InstallationHardware NotesTrouble Shooting
High Torque Hand Information
Use High Torque Clock Hands on larger clock dial diameters. Subsequently, these hands require a high torque clock movement that is run by a battery. Of course, these hands are for the American standard "I" shaft quartz movement that use a battery. The minute hand will have an oblong mounting hole and likewise the hour hand will have a round one. Altogether, the minute hand mounts on the oblong shaft of the clock movement. High torque hand information is important to know in order to choose the right ones.
Sold as a pair with both hour and minute hands. Styles vary depending on length and the longer hands will have a tail with counter balance.
Mounting the clock hands
The first piece of high torque hand information is mounting the clock hands. All in all, mounting the high torque hands to the high torque clock movement is easy. First, the hour hand is a friction fit so push it onto the post. Furthermore, push it down as far as it will go without it touching the clock face. Second is the minute hand which has the oblong hole. Similarly, it mounts on the tip of the oblong shaft of the movement. Finally, secure it with one of the hand nuts.
High Torque Hardware info
The second piece of high torque hand information is selecting the correct hand nut. There are two hand nuts that come with a new clock movement from Clockworks. One is a donut, which use with a second hand, and has a hole in it. Likewise, the other nut is a cap nut which has no hole and covers the entire tip of the post. Of course, a second hand requires the use of a donut and not a cap nut. This hardware comes with the purchase of a new movement, does not come with hands only purchase.
High torque hands checklist
That concludes the high torque hand information on the mounting procedure. To sum up, some things to look out for: the hour hand is not rubbing the dial and the minute hand is not rubbing the hour hand. Equally important, be certain the minute hand is not rubbing the glass door or anything else during its sweep around. In fact, these hands should be parallel and cannot come in contact with anything. If any of these things occur, the movement will not run. Not to mention, causing frustration in the process.
Quartz clock movement hardware for battery operated time only clock movements. The hardware pack includes rubber washer, the brass washer, a hex nut, a doughnut, and a cap nut. This hardware pack is for threaded posts that are 5/16 wide only. This is what the hex nut will screw onto, the 5/16 wide post.
Quartz Clock Movement Parts and Accessories
Quartz movement holder for mounting a wall clock. Holds a standard 2 1/8 square AA quartz movement. The clock dial can mount to this holder and then the clock can be hung on the wall. It will provide a wider base support against the wall and will not wobble around with long hands when a high torque unit is used.... View Product
Quartz Clock Movement Parts and Accessories
Holds a standard 2 1/8 square AA quartz movement. The clock dial can mount to this holder and then the clock can be hung on the wall. Provides a wider base support against the wall so it will not wobble around with long hands when a high torque unit is used. Can also be used as it is with the... View Product
Shop By Brand
Find the perfect Hermle movement for your clock.
Find the perfect Howard Miller movement for your clock.
Find the perfect Kieninger movement for your clock.
Find the perfect Seth Thomas movement for your clock.
Find the perfect Urgos movement for your clock.
Find the perfect Ridgeway movement for your clock.