If the clock has three places to wind with the key it is a quarterly chime unit. This means it is either Triple chime or Westminster only. In other words every 15 minutes it will progressively play part of the song. At the top of the hour it will play the complete song then strike out the hours.
So fastening it well is very important. The movement can have a pendulum or no pendulum but of course the pendulum is most popular. When a mechanical clock does not have a pendulum it has a balance wheel instead. This is a floating and rocking wheel on the top of the movement and operates more like a watch balance.
Mechanical Clock Kit Styles - Granddaughter or Grandmother clocks
Grandfather clock kits
This means the weights will hang on cables instead of chains, and plays choice of three songs. However it is not always triple chime because some are Westminster only. This is the largest and tallest of the floor clocks.
All of the above mechanical clock kit styles, in the past, have been made with every chime type. In other words there are all these various ways to make the clock play a song or make a noise.
There is the quarterly sounds that play a tune ever quarter hour, the most common of the songs is Westminster. Or there is the triple chime that includes Westminster, St. Michaels, or Whittington.
As for the other noise makers, we call them strike clocks because they only strike out the hours and usually bong once on the half hour. These include Gong strike (coil gong on the back or below the movement), Bell strike, or Bim Bam (sounds like its name, on two or three strike rods).
Mechanical clock-kit movement options
The following are the various options for Mechanical clock-kit movements to utilize in building a clock.
We offer complete kits at Clockworks, however we can't include them all as it would be overwhelming. It may be possible to alter any aspect in the clock kits that are available. Please call to let us help with kit modifications or for general assistance.
Mechanical clock-kit movement options - Floor Clocks
Either Westminster only or triple chime. Both of these Mechanical Clock Kit options play a melody every 15 minutes and require a three weight movement.
Also there is the bell strike option that will play on the top of the hour whatever hour it is, and once on the half hour.
Options are the length, the bob diameter, and if would like a wood stick style The Pendulum or a fancy lyre style The Pendulum. The wood stick style is more antique look and the lyre is the contemporary style.
Either on the back for standard depth cases, or for the shallow depth we can do a side hammer unit.
Mechanical clock-kit movement options - Wall Clocks
Either Westminster only, Triple chime, Bim Bam, gong or bell. Lots of chime options there, but whatever wanted to listen to out of these we can do.
Includes the back, or on the side, or even the bottom on the wall clock kits.
Square dial made of heavy paper stock that uses a spray glue in order to attach it to a thin board, or a metal dial.
One style you can't get these days are the round dials that do lock into the movement, to have the appearance of the dial just floating in the air with the mounting hidden such as the Vienna regulator style.
Mechanical clock-kit movement options - Mantle or Shelf Clocks
Mechanical clock-kit movement options - Chime type
All of them really. an have Westminster, triple chime, gong, bell, or Bim Bam strike for Mechanical clock movement kit options.
Mechanical clock-kit movement options - Pendulum
Options include metal rod to a decor for the kitchen style clocks are available, or a wood stick pendulum if the clock is tall enough. For the shorter mantle units it will be just a round bob that is usually adjustable for time keeping.
Mechanical clock-kit movement options - Dial
If the situation calls for this type of clock dial, may want to chase a different clock design to make, it is not often it works out well unfortunately. The shelf clocks are easier as it has a door that closes with glass in the front, rather than the round brass bezel with dial and glass all in one combination.
This concludes the Mechanical Clock-Kit movement options. Please call to discuss the clock kits with us 800 381 7458.
Clock kit before building the clock case
. This sounds crazy but it is more common than anyone may think. So before spending a lot of time and hard work on building a luxury case, take the advice of getting the clock kit first. It will save lots of frustration and money in the long run.
Why order a clock kit before building
Measurements need to be correct for the clock kit to fit into the case.
This way it will be easy to measure the various parts of the clock kit such as the pendulum swing and dial. Having the luxury of the components being in the air before you makes is much easier to measure and is a wise decision.
Not all clocks are made
The size of many antique clocks dials just are not made anymore. Grandfather clocks back in the day had large Clock dials with ships on them.
They most certainly are gorgeous but try to find another one like it. These are no longer available. This is the case with many others as well. This is yet another reason to buy the clock kit before building the case.
Alternate kit component availability
To sum up this topic on clock kits. It is wise to get the Mechanical Clock Kit before building the clock case. The best thing to do is set up the movement kit in the workshop. This way is easy access to visualize the size prior to installation.
Nothing is worse than making a beautiful case only to realize there are no components that will fit it. By purchasing all of the components before building, there is less chance for error when making the case. They will be at the disposal to measure at any time during the building process.
Making a Grandfather-Clock Seat-Board
Making a Grandfather-Clock Seat-Board, which is the mount that the weight driven movement sits upon, is fairly easy.
Typical approximate dimensions
Additionally, many of the modern clocks have a seatboard that is 16 inches wide and is 2 and a half inches deep. However this varies depending on the clock case dimensions.
In the center of the mounting board is a hole that is 1 inch wide. It goes across the center of the 2 and a half inch deep seat board.
Putting it together
These are the screws with the rectangle washers. Of course, an easier method would be to mount two, three quarter or 1 inch square boards running parallel, which are 1 inch apart, across the inside of the clock case. This is really all a mounting board needs to consist of.
The only thing that has to happen is the movement is in the air with the chains dangling down in between these boards. The boards just can’t be so wide that the pendulum rubs it on the back of the movement.
With the movement mounting in the air, all that needs to be done is have the chime block mounted.
This goes on the back of the clock case. This enables the hammers to engage with the rods for the chime sound. Next hang the weights and pendulum. The final step is to lock the dial into the movement from the front.
A plywood seat board
Many ways to make a seat board
A simple test stand
Clock case seat board
Grandfather Clock Pendulum Information
All three components in centimeters make up that CM length in the drop down menu.
Pendulum length information
Why the CM length matters at all is because if the pendulum length is not near the CM length of the movement, the clock will not keep time.
So the gearing in the movement and the pendulum length works together to keep time around the specified CM length.
The bob width Options
Moreover, the CM length on the movement will indicate the length of the pendulum from the TOP of the movement all the way down to the bottom of the pendulum nut threads.
This is an approximate length that depends on other factors such as bob diameter and weight of the pendulum.
Basically if the CM is 94CM the pendulum itself will be about 35 inches tip to tip off of the clock, and the 114CM option would put this same measurement at approximately 44 inches.
Round Dial Grandfather Clock-Kit
Round Dial Grandfather Clock-Kit has a German made triple chime, cable driven movement with second hand bit. This mechanical crank wound 8 day clock movement is the popular 1161-853 unit is made by Hermle Clock Company of Germany.Plays choice of three songs or silent, auto beat function and second hand sweep. This Round Dial Grandfather Clock-Kit includes everything, the Lyre pendulum, gong assembly, hands and hardware and weights. This is everything needed for a Round Dial Grandfather Clock-Kit except for the clock case.
The Mechanical Movement
1161-853 Hermle Clock Movement is a German made triple chime cable driven unit that takes three weights. This is a rectangle shaped movement with the movement plate size of 140 x 200mm and includes a size #8 crank.
About the Dial
Triple-Chime Grandfather Clock-Kit is Outfitted a Decorative white Roman numeral dial that is There are feet coming out the back of the dial that lock into the front plate of the movement. The dial is an easy install because the movement has levers behind the front plate that one just uses the fingers to push the lever and lock the dial foot post. White dial with 10-5/8” time track. 1-3/4” seconds circle with 1-3/8” time track. Slot for chime settings at III. “Hermle” logo below the 9mm winding arbor hole. Brass bezel. Four 1-11/16” mounting pins on reverse. 9mm winding arbor holes on 5-5/8” centers.
The Pendulum CM Length
The Lyre pendulum can come in a variety of lengths. This is indicated by the CM number on the back plate of the movement. However this CM length is the entire pendulum assembly and not just the pendulum. So this CM includes the leader, the suspension spring, and the pendulum tip to tip. This length also varies some due to the weight of the pendulum, and also the bob diameter.
Assistance = 800-381-7458
- Hermle 1161-853
- Triple Chime
- Cable Driven
- 11 7/8 Dial
- Lyre Pendulum
- Back 12 Rod Strike
- Movement = 140 x 220mm
- Serpentine Hands
- Made in Germany
- 3-year warranty